Manuals / Cal Flame / Lawn and Garden / Hot Tub

Cal Flame A734B, A515, A734L, A534, A726B Volt Electrical Installation, Testing the GFCI Breaker

Models: A526 A726L A726B A534 A734L A515 A734B

1 32

Download 32 pages 61.6 Kb

Page 14

120 Volt Electrical Installation

120 Volt Electrical Installation

Always follow applicable local, state and federal codes and guidelines.

Use only a dedicated electrical line with a 20-amp breaker.

Cord-and-plug connections may not use a cord lon- ger than 15 ft (4.6 m) and must be plugged into a dedicated 20-amp GFCI connection. Do not use extension cords!

Always use a weatherproof-covered receptacle.

Receptacle shall be located not less than 5 ft (1.5 m)

from and not exceeding 10 ft (3.0 m) from the inside wall of the spa. Do not bury the power cord.

If your cord becomes damaged, replace it before next usage.

All 120V spas must have a GFCI. This can be either a 20-amp GFCI re- ceptacle or a GFCI cord and plug kit as shown at right (CKIT110 - P/N ELE09700086).

Testing the GFCI Breaker

Test the GFCI plug prior to first use and periodically when the spa is pow- ered. To test the GFCI plug version, follow these instructions. (Spa should already be plugged in and operational.)

1.Press the TEST button on the GFCI. The GFCI will trip and the spa will stop operating.

2.Press the RESET button on the GFCI. The GFCI will reset and the spa will turn back on.

The spa is now safe to use.

If the GFCI trips while the spa is in use, press the RESET button. If the GFCI does not reset, unplug the spa and call your local Cal Spas dealer for service. DO NOT USE THE SPA!

12	LTR20091024, Rev. A

Image 14

Cal Flame A734B, A515, A734L, A534, A726B, A726L, A526 manual Volt Electrical Installation, Testing the GFCI Breaker

Contents

Page Contents Pre-DeliveryChecklist Pre-Deliveryand Installation ChecklistPre-DeliveryChecklist Portable SpaPlanning the Best Location Safety firstKeep your spa clean Consider how you will use your spaLTR20091024, Rev. A Allow for service accessOutdoor equipment pack in-groundspas only Portable Spa Site Preparation In-GroundSpa Site PreparationSite Excavation - Sand Bottom Grading Prior to ExcavationSite Excavation - Hard Bottom LTR20091024, Rev. APlan the Delivery Route Check the Dimensions of Your New SpaGetting the Spa Into Your Yard Special CircumstancesLTR20091024, Rev. A Electrical Requirements 240 Volt Electrical InstallationGFCI and Wiring Requirements Electrical Requirements - US and CanadaGFCI Required Wires RequiredSpa Model LTR20091024, Rev. A Testing the GFCI BreakerConfiguring the 6300 Control System GFCI Wiring Diagram LTR20091024, Rev. A120 Volt Electrical Installation Testing the GFCI BreakerRCD and Wiring Requirements Electrical Installation --Europe230 Volt Electrical Installation Testing the RCD BreakerGFCI Required Wires RequiredSpa Model All 230V spas exceptRCD Wiring Diagram LTR20091024, Rev. AInstalling the In-GroundShell LTR20091024, Rev. ADIJ401 and DIJ405 Designer Spa SpecificationsEquipment Pack Plumbing Connections In-GroundSpas DIJ407LTR20091024, Rev. A Air Test In-GroundPlumbing ConnectionsIdentifying Plumbing Lines Water TestLTR20091024, Rev. A Connecting Plumbing to Remote EquipmentGate/Slice Valves Electrical and Electronic Connection Remote Equipment Topside Control Panelat least 4” 10 cm above ground level, and In-GroundSpa Light Installation Instructionsat least 8” 20 cm above water level at least 48” 121 cm away from the spaLTR20091024, Rev. A LTR20091024, Rev. A Pouring the In-GroundSpa Deck LTR20091024, Rev. ASpa Technical Specifications Classic Series Family II Series Ultimate Fitness and Fitness Pro Series LTR20091024, Rev. A 12/15/08