Campbell Hausfeld IFN2190, IFN3490 operating instructions Sujetadores

Manual de Instrucciones Modelo IFN3490 and IFN2190

Operating Instructions Model IFN3490 and IFN2190

Unidos continentales, comuníquese con nosotros al 1-513-3678-1182.

Clavos et Repuestos

Use solamente sujetadores Campbell Hausfeld originales (o su equivalente) - (vea la información sobre intercambio de sujetadores). Use solamente partes de repuesto Campbell Hausfeld originales. Nunca substituya las partes. No use partes modificadas o partes que no den un rendimiento equivalente al equipo original. El rendimiento de las herramientas, la

seguridad y la duración pueden verse reducidos. Cuando ordene partes de repuesto o sujetadores, especifique el número de la parte.

Para reparar la clavadora

Las reparaciones de la clavadora las debe hacer SOLAMENTE un técnico calificado que tenga experiencia.

Para colocarle los sellos

Cada vez que repare una clavadora deberá limpiarle y lubricarle las partes internas. Le recomendamos que use

Parker O-lube o un lubricante equivalente en todos los anillos en O. A cada anillo en O se le debe dar un baño de lubricante para anillos antes de instalarlos. Igualmente, deberá ponerle un poco de aceite a todas las piezas que se mueven y muñones. Finalmente, después de haberla ensamblado y antes de probar la herramienta deberá ponerle unas cuantas gotas de aceite sin detergente 30W u otro aceite similar, en las líneas de aire.

compressor manufacturer for information.

Operating The Nailer

Read this manual and understand all safety warnings and instructions before operating the nailer.

LUBRICATION

This nailer requires lubrication before using the nailer for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis.

NOTICE

The work surface

RECOMMENDED HOOKUP
1. The air	70 psi
compressor
	Min.
must be able	120 psi
to maintain a
	Max.
minimum of 70

psi when the nailer is being used. An inadequate air supply can cause a loss of power and inconsistent driving.

2. An oiler can be used to provide oil circulation through the nailer. A filter

REMOVING NO-MAR DECKING TIP

1. Disconnect air supply from nailer.

2.Remove all fasteners from magazine (See UNLOADING THE

NAILER).

3.Remove no-mar tip retaining ring.

Retaining

Ring

Sujetadores

La herramienta IFN2190 también coloca sujetadores diseñados para: Sears 18465, Porter Cable FR350, Hitachi NR83A, y Senco FramePro 702XP, 752XP, Ridgid R350RHA y DeWalt D51844, D51845.

La herramienta IFN3490 también coloca sujetadores diseñados para: Porter Cable FC 350A, Hitachi NR83AA2, Senco FramePro 701XP, 751XP , Ridgid R350CHA, DeWalt D51822, D51823 y Paslode F-3505.

can become

damaged by excessive lubrication. Proper lubrication is the owner’s responsibil- ity. Failure to lubricate the nailer properly will dramatically shorten the life of the nailer and void your warranty.

1. Disconnect the air supply from the nailer to add lubricant.

2. Turn the nailer
so the air inlet	OIL
is facing up.
Place 4-5 drops
of 30 W non-
detergent oil
into air inlet.
Do not use
detergent oils, oil additives, or air
tool oils. Air tool oils contain
solvents which will damage the
nailer’s internal components.

3. After adding oil, run nailer briefly. Wipe off any excess oil from the cap exhaust.

can be used to remove liquid and

solid impurities which can rust or “gum up” internal parts of the nailer.

3. Use 3/8” air

hoses with a minimum working

pressure of 150 psi. Use 1/2” air hoses for 50’ run or longer. For better performance, install a 3/8” quick plug (1/4” NPT threads) with an inside diameter of .315” (8mm) on the nailer and a 3/8” quick coupler on the air hose.

4.Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the nailer between 70 and 120 psi.

NO-MAR DECKING TIP

The no-mar decking tip is designed to eliminate marks caused by the serrated work contact element (WCE). The no- mar tip may be removed if not required (See REMOVING NO-MAR DECKING TIP). Use tool in single cycle mode (SEE OPERATIONAL MODES) when no-mar tip is in place.

No-Mar Tip

4. Pry no-	No-
mar tip
away	Mar
from the	Tip
work
contact	Work
element.	Contact
	Element

5.Replace retaining

ring onto

no-mar

tip, then store tip in safe

place for future use.

INSTALLING NO-MAR DECKING TIP

1. Disconnect air supply from nailer.

2.Remove all fasteners from magazine (See UNLOADING THE NAILER).

3.Remove retaining ring from no-mar tip.

www.chpower.com

6-Sp

Recommended Hookup
Quick	Quick	Quick Plug	Regulator
		(Optional)	Oiler
Plug	Coupler
		Quick
		Coupler
		(Optional)
		Air
		Hose
			Filter
		3