Manuals / Carrier / Kitchen Appliance / Water Dispenser

Carrier Application data cont, 23XRV NOZZLE ARRANGEMENTS cont, Discharge End, Suction End

Models: 23XRV

1 32

Download 32 pages 17.21 Kb

Page 20

Image 20

Application data (cont)

23XRV NOZZLE ARRANGEMENTS (cont)

MARINE WATERBOXES

DISCHARGE END

SUCTION END

FRAME 3

NOZZLE ARRANGEMENT CODES

		COOLER WATERBOXES
PASS	In	Out	Arrangement
	In	Out	Code
			Code
1	8	5	A
1	5	8	B
	5	8	B

2	7	9	C
2	4	6	D
	4	6	D

3	7	6	E
3	4	9	F
	4	9	F

		CONDENSER WATERBOXES
PASS	In	Out	Arrangement
	In	Out	Code
			Code
1	—	—	—
1	—	—	—
	—	—	—

2	10	12	R
2	1	3	S
	1	3	S

3	—	—	—
3	—	—	—
	—	—	—

DISCHARGE END

SUCTION END

FRAMES 4, AND 5

NOZZLE ARRANGEMENT CODES

		COOLER WATERBOXES
PASS	In	Out	Arrangement
	In	Out	Code
			Code
1	9	6	A
1	6	9	B
	6	9	B

2	7	9	C
2	4	6	D
	4	6	D

3	7	6	E
3	4	9	F
	4	9	F

		CONDENSER WATERBOXES
PASS	In		Out	Arrangement
	In		Out	Code
				Code
1	—		—	—
1	—		—	—
	—		—	—

2	10		12	R
2	1		3	S
	1		3	S

3	—		—	—
3	—		—	—
	—		—	—

Page 20

Image 20

Carrier manual Application data cont, 23XRV NOZZLE ARRANGEMENTS cont, Discharge End, Suction End

Contents

Features/Benefits SEISMICOMPLIANTProduct reliability Product DataFeatures/Benefits cont Table of contentsHigh efficiency Environmental leaderHeat exchanger features Microprocessor controls featuresModel number nomenclature Features/Benefits contSEISMICOMPLIANT Quality AssurancePhysical data 23XRV COMPRESSOR AND MOTOR WEIGHTSCOMPONENT WEIGHTS 23XRV HEAT EXCHANGER WEIGHTSPhysical data cont ADDITIONAL WEIGHTS FOR 23XRV MARINE WATERBOXES23XRV WATERBOX COVER WEIGHTS - ENGLISH lb 23XRV WATERBOX COVER WEIGHTS - SI kg→ Options and accessories Dimensions a23-164623XRV DIMENSIONS 23XRV DIMENSIONS NOZZLE-IN-HEAD WATERBOX23XRV HEAT EXCHANGER MIN/MAX FLOW RATES Performance dataNOZZLE SIZE AUXILIARY RATINGS Electrical dataVFD FRAME SIZES Features ControlsMicroprocessor controls Control systemControls cont CONTROL PANEL DISPLAY Front ViewCONTROL PANEL DISPLAY Front View ICVC ENGLISH DISPLAY IN SI UNITSCCN COMMUNICATION WIRING FOR MULTIPLE CHILLERS TYPICAL Control sequence Controls contTypical piping and wiring 23XRV CHILLERControl wiring schematic 23XRV COMPONENT ARRANGEMENT→ 23XRV MACHINE FOOTPRINT Application dataa23-1650 23XRV ISOLATION WITH ACCESSORY SOLEPLATE PACKAGE Application data conta23-1647 23XRV NOZZLE ARRANGEMENTS DISCHARGE ENDDISCHARGE END SUCTION ENDApplication data cont 23XRV NOZZLE ARRANGEMENTS contDISCHARGE END SUCTION END23XRV WATERBOX NOZZLE SIZES Nozzle-In-Head and Marine Waterboxes RELIEF VALVE LOCATIONSRELIEF VALVE ARRANGEMENTS WITH OPTIONAL ISOLATION OF DISCHARGE AND COOLERVent and drain connections Relief valve discharge pipe sizingASME stamping Design pressures→ Minimum fluid loop volume Insulation23XRV MINIMUM FIELD-INSTALLED INSULATION REQUIREMENTS CONDENSATION VS RELATIVE HUMIDITYVariable Speed Screw Chiller Guide specificationsHVAC Guide Specifications 1. Temperature is between 40 F 4.4 C and 120 F 48.9 C 1.04 WARRANTY2. Relative humidity is between 10% and 80% non-condensing Part 2 - Products 2.01 EQUIPMENT A. GeneralGuide specifications cont 7. VFD Electrical Service single point power e. Input power shall be 380/460 vac, ±10%, 3 Phase, 50/60 Hz, ±2% Hzc. Condenser water pump d. Alarm status 9. Analog Output b. Over voltage c. Phase loss d. Phase reversal e. Ground faultGuide specifications cont F. Refrigerant Flow Controll. Chilled Water Reset 1 Chilled water reset based on an external 4 to 20 mA signal2 Demand limit based on external 4 to 20 mA signal 4 Single cycle dropout 5 Low oil sump temperatureGuide specifications cont H. Electrical RequirementsThese items shall be factory-installed to allow or condenser with 1, 2 or 3 pass configurationA refrigerant pumpout system shall be installed piping, internal wiring, andCarrier Corporation Syracuse, New York 5-10Section Catalog No