Carrier 592-085 warranty P.Lateral Duct System optional

P.Lateral Duct System (optional):

The lateral duct system shall allow one system to heat or cool two adjacent rooms, with up to a maximum of 30% of the discharge air being diverted to the adjoining room (a return air path must be provided from the adjoining room). The lateral duct kit consists of two main components, the plenum and the extension duct. In addition, the kit includes an adjustable chassis discharge air grille, adjustable wall register and decorative wall molding for duct extension.

The Lateral Duct system shall be adaptable for either right or left side ducting, with a maximum duct extension of 4 feet. The duct run must be straight and horizontal; no bends or turns.

Q.Accessories:

1.Insulated Polymer Wall Sleeve (P/N: SLEEVE-INSUL-1PK) shall be made from a molded polymer, with factory-installed Styro- foam insulation and a minimum flammability rating of UL94-5V. The sleeve surface shall be textured to prevent shine and hide scratches.

2.Deep Wall Metal Wall Sleeve (up to 28-in.) (P/N: SLEEVE-EXTxx-1PK) shall be a one- piece, extended wall sleeve, with factory installed insulation and deep wall baffles integrated.

3.Sleeve Molding (P/N: SLEEVE-MOLDING) shall trim the wall sleeve to the existing wall to hide wall joints and irregularities due to the sleeve opening.

4.Architectural Grille (P/N: GRILLE-PLA- xxxxx or GRILLE-ALU-xxxxx) shall be poly- meric for long durable life or painted alumi- num for a superior color match to the building.

5.Subbase (P/N: SUBBASE-xxxV-xxA) shall be pre-assembled from the factory and UL listed. Subbase options include:

Non-electrical subbase: The non-electrical subbase shall be pre-assembled and provides mechanical support and requires no wiring.

Electrical subbase: The electrical subbase shall be pre-assembled with factory-installed electrical junction box containing a receptacle for corded units.

Hardwired subbase: The hardwired electrical subbase shall be pre-assembled with factory installed electrical junction box containing 19 in. of flexible conduit (for a perfect fit to the unit) and all mating connections.

6.Leveling Legs (P/N: LEVELING-LEGS) shall attach easily to Carrier’s wall sleeve to provide accurate, adjustable leveling and support to units without a subbase.

7.Hardwire Kit (P/N: HARDWIRE-KIT) shall provide a permanent connection to the unit.

The hardwire kit mounts on the front right side of the unit and shall have 36 in. of flexible steel conduit and a Molex connector for easy connect/disconnect.

8.Conduit Interface Kit (P/N: CONDUIT-INTF- 4PK) shall provide wire connection to the unit to interface with field-supplied conduit.

9.Condensate Drain (P/N: DRAIN-KIT-4PK) kit shall be used internally or externally to route excess condensate to a drainage system. It can be field-installed on any Carrier wall sleeve. The drain kit shall be attached to the exterior right or left side of the wall sleeve for external draining or may be mounted to the bottom of the wall sleeve for internal draining.

10.Lateral Duct (P/N: LATERAL-DUCT) kit shall include an adapter plenum, extension duct, wall register and wall molding. The lat- eral duct system allows one system to heat or cool two adjacent rooms, by directing up to 30% of the airflow to the adjacent room. See section 4.0 for detailed specification.

11.Energy Management (P/N: EM-KIT) shall allow individual units to be turned on and off from a remote location or by a motion sensing device. This kit interfaces to most energy man- agement systems.

12.Lateral Air Deflector (P/N: DEFLECTOR- 1PK) shall allow right or left air distribution from the chassis. Lateral air deflectors are rec- ommended for units mounted in a corner or off-center in a room.

13.Curtain Deflector (P/N: CURTDEL-52CP- 1PK) shall prevent curtains from being blown into the discharge air.

14.Security door (P/N: SECURITY-DOOR) kit shall prevent unauthorized access to the unit’s heating and cooling controls and prevents tampering with units in public locations and institutions. The security door shall include two matching keys and keys shall be common to all Carrier Security Door kits.

15.Wall Thermostats (P/N: TSTATCCBxx01-B) shall operate with 24 VAC, be digital and non-programmable, easy-to-use and provide maximum guest comfort.

16.Sleeve Molding (P/N: SLEEVE-MOLDING) shall trim the wall sleeve to the existing wall to hide wall joints and irregularities due to the sleeve opening.

17.Power Fresh Air Vent (P/N: PWR-VENT- DOORxxx) kit shall provide approximately 95 cfm of outdoor air for ventilation into the room. The kit shall have an automatically door that opens when the fan is on and closes when the fan is off.

53