SAFETY CONSIDERATIONS
Installation Instructions
CONTENTS
GENERAL
Step 6 - Install Field-FabricatedDuctwork
INSTALLATION
Step 5 - Install Curb Gasketing
Step 1 - Perform Jobsite Survey - Complete
Table 1A - Physical Data 48P2,P3,P4,P5030-050
Table 1A - Physical Data 48P2,P3,P4,P5030-050cont
Table 1B - Physical Data 48P2,P3,P4,P5055-070
Table 1C - Physical Data 48P2,P3,P4,P5075-100
Table 1C - Physical Data 48P2,P3,P4,P5075-100cont
Table 4 - Optional Humidi-MiZer Coil Data
Table 6 - Supply Fan Drive Data
Table 7 - Power Exhaust Fan Drive Data
Table 9 - Optional Return Fan Drive Data
Fig. 1 - Roof Curb - Sizes
Fig. 2 - Roof Curb - Sizes
Fig. 3 - Roof Curb - Sizes
Page
Page
9 3/4
CONDENSER END SUPPORT
4 REF
X NO GASKET
With field-suppliedfittings and pipe sections, plumb the pri- mary condensate drain to the 2-in.FPT connector on the base rail. Use a trap height of at least 4-in.for size 030-070units and 7-in.for size 075-100units. See Fig. 23 and 24. Install with a height dimension of at least 2-in.from the top of the exit pipe from the trap section to the bottom of the connector. Apply a bead of RTV or similar sealant around the pipe joint at the con- nector in the base rail
a48-8455
ALL PANELS MUST BE IN PLACE WHEN RIGGING
CAUTION - NOTICE TO RIGGERS
UNITS
CAUTION - NOTICE TO RIGGERS
ALL PANELS MUST BE IN PLACE WHEN RIGGING
WEIGHT
a48-8456
48P2,P3,P4,P5 UNITS
Locate the four 11/4-in.drain coupling assemblies and mounting screws shipped in a bag taped to the basepan in the supply fan section, located behind the access panel marked FAN SECTION. The drain couplings are a 10-gageplate with a 11/4 in. half coupling welded to the plate
a48-8613
a48-8614
a48-8615
a48-8616
a48-8617
a48-8618
a48-8619
a48-8620
a48-8621
a48-8622
Location Curb Mount
a48457
Fig. 25 - Secondary Condensate Drain
Fig. 23 - Primary Drain Connection
a48-8459
Fig. 28 - Outdoor Air Hood Installation Sizes
Installation Sizes
Fig. 27 - Secondary Drain Seal Plate
Fig. 32 - 25% Outdoor-AirHood Location
Step 10 - Install Economizer Hoods Units
Installation Sizes
Fig. 33 - Economizer Outdoor-AirHood
Fig. 37 - Large Economizer Hood Assembly
a48-8462
Step 11 - Route Field Wiring
Step 12 - Make Field Electrical Connections
a48-8465
a48-8463 a48-8464
Fig. 39 - Disconnect Location - Size 040-060Units
Fig. 40 - Disconnect Location - Size 070-100Units
for Factory-InstalledDisconnect
Fig. 41 - Field Power Wiring Connections
Fig. 43 - Field Power Wiring Connections
a48-8467
VOLTAGE
VOLTAGE
VOLTAGE
VOLTAGE
174.0/171.8
70.8
225.4/223.2
78.1
Page
Page
Page
VOLTAGE
14.0
27.0
208.4
14.0
27.0
219.8
14.0
27.0
Fig. 44 - Auxiliary Control Box Location Sizes
Fig. 47 - Auxiliary Control Box Details
Fig. 45 - Auxiliary Control Box Location Sizes
Fig. 46 - Auxiliary Control Box Details
Sizes
Fig. 49 - Shipping Brackets Size 030-050Units
Fig. 48 - Auxiliary Control Box Details
Size 075-100Units with Optional Return Fan
Fig. 50 — Shipping Brackets Size 055-070Units
Fig. 51 - Shipping Brackets Sizes
Fig. 52 - Optional Return Fan Shipping Brackets
Fig. 55 - Flue/Inlet Hood Locations, Sizes
Fig. 53 - Gas Piping Details
Fig. 54 - Flue/Inlet Hood Locations, 030-050Units
Low Heat, Vertical Supply Units
Fig. 56 - Flue/Inlet Hood Locations, Sizes
a48-8471
a48-8584
Fig. 58 - Baffle Location, 030-050Units
a48-8587
Fig. 61 - Flue Outlet Hood
Fig. 60 - Baffle Locations, Sizes
Horizontal Supply Units
a48-8588
Fig. 65 - Inlet Hood Assembly 6-in.and 14-in
Installation
Fig. 63 - Flue Deflector Baffle Curve-Type
Fig. 68 - Air Baffle 14-in
Fig. 67 - Inlet Hood Assembly 30-in
a48-8473
a48-8590
a48-8560
a48-8561
Fig. 70 - Wind Baffle Details
CONTROLS INSTALLATION
Fig. 73 - Space Temperature Averaging Wiring
Fig. 72 - T55 or T56 Wiring
Fig. 71 - Field Control Thermostat Wiring
a48-8474TB201
Fig. 76 - CO2 Space Sensor Wiring
Fig. 74 - Heat Interlock Relay Wiring
Fig. 75 - Outdoor Air Enthalpy Switch Wiring
Fig. 77 - Filter Status Wiring
RED BRN
Fig. 78 - Fan Status Switch Wiring
Fig. 80 - Return Air CO2 Sensor Wiring
a48-8482
TB201
Fig. 81 - Return Air Smoke Detector Wiring
Fig. 82 - Fire Shutdown Wiring
FIRE SHUTDOWN
Fig. 84 - CCN Connections
Carrier Comfort Network CCN Interface
a48-8487
Table 28 - CCN Connection Approved
Optional UPC Open Installation
Table 29 - MS/TP Wiring Recommendations
turning the supply fan off
See Fig. 82 for wiring
Fig. 85 - UPC Open Controller
opening the economizer option required
Fig. 86 - BT485 Installation
Fig. 86 - Open System Network Wiring
Table 31 - Smoke Control Modes