Casio WK3200, WK3700 Renaming a File, Deleting a File, button, to rename, the “Rename” screen, name selection screen, file name input screen, Mode (or Disk Mode) menu

Saving Data

Renaming a File			6 Press the [￿] CURSOR button to display the file
You can use the procedures in this section to change the name				name selection screen.
of a file that you previously saved to external storage media.			7 Use the [￿] and [￿] CURSOR buttons or [+] and
PREPARATION				[–] buttons to select the name of the file you want
				to rename.
•	SmartMedia Card
				• You could also use the number buttons to input a
	• Insert the SmartMedia card that contains the file you
				three-digit file number. The file number is shown in
	want to rename into the keyboard’s card slot. Make
				the number area of the display.
	sure that the sticker is removed from the card’s write
	area, which enables writing.		8 Press the [￿] CURSOR button to advance to the
•	Floppy Diskette (WK-3700 Only)
				file name input screen.
	• Insert the floppy diskette that contains the file you want
	to rename into the keyboard’s floppy disk drive. Make			• Use the [+] and [–] buttons to scroll through letters at
	sure that the diskette’s write protect hole is closed,			the current cursor location. See the page E-92 for
	which enables writing.			information about inputting text.
				• Use the [￿] and [￿] CURSOR buttons to move the
				cursor left and right.
To rename a file saved to external storage media			9 After inputting the file name, press the [￿] CURSOR
1 What you should do first depends on the type of				button.
	external storage media you are using.			• This will display a confirmation message asking
				whether you really want to change the name.
	• SmartMedia Card
			0 Press the YES button to change the file name.
	On the WK-3700 press the DISK/CARD button twice.
	On the WK-3200, press the CARD button once.			• This will cause the message “Pls Wait” to appear on
	• This causes a pointer to appear next to the DISK/
				the display to indicate that a card access operation is
		CARD or CARD on the display, and also displays
				being performed. Never try to perform any other
		“Card” in the display’s text area.
				operation on the keyboard while the card is being
	• Floppy Diskette (WK-3700 Only)
				accessed. The message “Complete” will appear on the
	Press the DISK/CARD button.
				display after renaming is complete. After a few
	• This causes a pointer to appear next to the DISK/
				seconds, the message will be replaced by the file name
		CARD on the display, and also displays “Disk” in
				selection screen.
		the display’s text area.
				• If you do not want to continue with file renaming,
NOTE				press the EXIT button or the NO button in response
				to the above confirmation message. This will return
• After pressing the DISK/CARD button (WK-3200: CARD				you to the file selection screen.
	button) once, you can use the [￿] and [￿] CURSOR		A After you are finished performing the rename
	buttons to select the external storage media.
				operation, press the DISK/CARD button (CARD
2 Press the [￿] CURSOR button to display the Card				button on the WK-3200) to exit the Card Mode.
	Mode (or Disk Mode) menu.
3 Use the [￿] and [￿] CURSOR buttons to display			Deleting a File
	the “Rename” screen.		You can perform the procedure in this section to delete a file
4 Press the [￿] CURSOR button to advance to the			from external storage media.
	file type selection screen.		IMPORTANT!
5 Use the [￿] and [￿] CURSOR buttons to select the			•	Note that the file delete operation cannot be undone.
				Make sure that you no longer need data before you
	type of the file you want to rename.			delete it.
			•	Deleting a file causes all of the file numbers following it
				to be reduced by one. If you plan to delete another file,
				make sure that you do not specify the wrong file number.

E-90 738A-E-092A