Manuals / Cisco Systems / Computer Equipment / Computer Hardware

Cisco Systems 1130AG Director Corporate Compliance, Cisco Systems Inc, Declaration Of Conformity

Models: 1130AG

1 126

Download 126 pages 59.84 Kb

Page 100

DECLARATION OF CONFORMITY

Appendix B Declarations of Conformity and Regulatory Information

Declaration of Conformity Statements

DECLARATION OF CONFORMITY

with regard to the R&TTE Directive 1999/5/EC

according to EN 45014

Cisco Systems Inc.

170 West Tasman Drive

San Jose, CA 95134 USA

Declare under our sole responsibility that the product,

Product: AIR-AP1131AG-E-K9

Variant: AIR-LAP1131AG-E-K9

Cisco Aironet 1130AG Series IEEE802.11 a/b/g Access Point

Fulfils the essential requirements of the Directive 1999/5/EC

The following standards were applied:

EMC	EN 301.489-1 v1.4.1: 2002-08; EN 301.489-17 v1.2.1: 2002-09
Health & Safety	EN60950: 2000; EN 50385: 2002
Radio	EN 301.893 v 1.2.3: 2003-08
	EN 300 328 v 1.4.1: 2003-04

The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed.

The product carries the CE Mark:

Date & Place of Issue:

25 July 2005, San Jose

Signature:

	Tony Youssef
	Director Corporate Compliance
	Cisco Systems, 125 West Tasman Drive	DofC 441919rev1
	San Jose, CA 95134 - USA	DofC 441919rev1
	San Jose, CA 95134 - USA

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

	B-12	OL-8369-05

Image 100

Cisco Systems 1130AG Director Corporate Compliance, Cisco Systems Inc, Declaration Of Conformity, Signature, Tony Youssef

Contents

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide JuneAmericas Headquarters Cisco Systems, Inc 170 West Tasman Drive San Jose, CATurn the television or radio antenna until the interference stops Guidelines for Using 1130AG Series Lightweight Access Points Repeater Unit that Extends Wireless RangeC O N T E N T S PrefaceAccess Point Layout and Connectors Opening the Access Point CoverUsing a Security Cable Security SettingsConnecting to the Access Point Console Port Guidelines for Using 1130AG Series Lightweight Access PointsResetting to the Default Configuration Using the Web Browser InterfaceDeclarations of Conformity and Regulatory Information B-1 Industry Canada B-4Translated Safety Warnings Access Point SpecificationsContents Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-8369-05 G L O S S A R Y I N D EContents Cisco Aironet 1130AG Series Access Point Hardware Installation Guideviii OL-8369-05Preface AudiencePurpose OrganizationConventions Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät liitteestä Translated Safety Warnings käännetyt turvallisuutta koskevat varoitukset Related Publications Obtaining Documentation, Obtaining Support, and Security GuidelinesSN AAANNNNXXXX Locating the Product Serial Numberxiii Preface Locating the Product Serial Number Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-8369-05 Autonomous Access Points Lightweight Access PointsOverview Product TerminologyGuidelines for Using 1130AG Series Lightweight Access Points Hardware Features Single or Dual-Radio Operation Ethernet PortConsole Port LEDsPower Sources UL 2043 CertificationAnti-Theft Features Network Examples with Autonomous Access Points Figure 1-3 Access Point Security Screw HoleRoot Unit on a Wired LAN Figure 1-4 Access Points as Root Units on a Wired LANRepeater Unit that Extends Wireless Range Figure 1-5 Access Point as RepeaterCentral Unit in an All-Wireless Network Workgroup Bridge ConfigurationFigure 1-6 Access Point as Central Unit in All-Wireless Network Figure 1-7 Workgroup Bridge ConfigurationFigure 1-8 Workgroup Bridge Configuration Network Example with Lightweight Access Points1-11 Chapter 1 Overview Network Example with Lightweight Access Points Cisco Aironet 1130AG Series Access Point Hardware Installation Guide1-12 OL-8369-05Installing the Access Point C H A P T E RSafety Information FCC Safety Compliance StatementGeneral Safety Guidelines WarningsUnpacking the Access Point Package ContentsBasic Installation Guidelines Controller Discovery Process for Lightweight Access PointsDeploying the Access Points on the Wireless Network Access Point Layout and Connectors Figure 2-1 Access Point Hardware FeaturesMounting Plate Mounting PlateSuspended Ceiling Adjustable T-Rail Clips T-rail locking screws Figure 2-4 Adjusting the T-Rail Clips Chapter 2 Installing the Access PointDeploying the Access Points on the Wireless Network Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOpening the Access Point Cover 2-11Mounting the Access Point on a Horizontal Surface 2-12Figure 2-7 Adjustable T-Rail Clips Mounting the Access Point Below a Suspended Ceiling2-13 Mounting the Access Point Above a Suspended Ceiling 2-14Suspended ceiling T-rail 2-15Mounting Access Point on a Network Cable Box Mounting Access Point on a Desktop or ShelfAttaching the Access Point to the Mounting Plate 2-16Figure 2-10 Aligning the Keyhole Clip to the Access Point Keyhole 2-17Using a Security Cable Securing the Access Point2-18 Figure 2-12 Installing the Security Hasp Adapter Securing the Access Point to the Mounting Plate2-19 2-20 PadlockConnecting the Ethernet and Power Cables OptionOption Option2-22 Connecting to an Ethernet Network with an Inline Power SourceFigure 2-15 Looping the Ethernet Cable Connecting to an Ethernet Network with Local Power 2-232-24 Rotating the Cisco LogoFigure 2-16 Cisco Logo Holes Troubleshooting Autonomous Access Points C H A P T E RChecking the Autonomous Access Point LEDs Figure 3-1 Access Point LEDsCable Bay Area Top of UnitMessage type Ethernet LEDChecking Basic Settings Default IP Address BehaviorDefault SSID and Radio Behavior Cable Bay AreaEnable Radio Interfaces Security SettingsSSID WEP KeysLow Power Condition for Autonomous Access Points Intelligent Power ManagementInline Power Status Messages Note A Cisco power injector might be required Note A Cisco power injector might be required Configuring Power Using the CLI 3-10Issuing the Cisco IOS Command Using the CLI Cisco IOS CommandsPower Source Access PointConfiguring the Access Point System Power Settings Using a Browser Cisco SwitchPower Source Access Point System Power SettingsCisco Switch Power SourceAccess Point System Power Settings Power CommandRunning the Carrier Busy Test 3-14Running the Ping Test Resetting to the Default Configuration3-15 Using the Web Browser Interface Using the MODE Button3-16 Reloading the Access Point Image Using the MODE ButtonStep 7 Click Reset to Defaults 3-17Browser HTTP Interface Web Browser Interface3-18 Obtaining the Access Point Image File Browser TFTP InterfaceClick Access Points Cisco Aironet 1130 AG Series Click Cisco Aironet 1130AG Access Point3-20 Connecting to the Access Point Console PortStep 13 Click DOWNLOAD Obtaining the TFTP Server Software 3-21Chapter 3 Troubleshooting Autonomous Access Points Cisco Aironet 1130AG Series Access Point Hardware Installation Guide3-22 Obtaining the TFTP Server SoftwareTroubleshooting Lightweight Access Points C H A P T E RUsing DHCP Option Checking the Lightweight Access Point LEDsGuidelines for Using 1130AG Series Lightweight Access Points Figure 4-1 Access Point LEDs Top of Unit Message typeEthernet LED Radio LEDTop of Unit Message typeEthernet LED Radio LEDLow Power Condition for Lightweight Access Points Intelligent Power Management1 config ap power pre-standard enable ap Configuring Power Using Controller CLI Commands2 config ap power injector enable ap switch port MAC address CLI Commands Power SourceCisco Wireless LAN Controller Cisco SwitchReturning the Access Point to Autonomous Mode Configuring Controller InformationManually Resetting the Access Point to Defaults Clearing Manually Entered Controller InformationUsing the MODE Button to Return the Access Point to Autonomous Mode Using a WLAN Controller to Return the Access Point to Autonomous Mode4-10 Obtaining the Autonomous Access Point Image File MODE Button SettingStep 3 Click Cisco Aironet 1130AG Access Point 4-114-12 Connecting to the Access Point Console PortFigure 4-2 Console Port Location http//tftpd32.jounin.net Obtaining the TFTP Server Software4-13 Chapter 4 Troubleshooting Lightweight Access Points Cisco Aironet 1130AG Series Access Point Hardware Installation Guide4-14 Obtaining the TFTP Server SoftwareTranslated Safety Warnings A P P E N D I X ACisco Aironet 1130AG Series Access Point Hardware Installation Guide Appendix A Translated Safety WarningsOL-8369-05 Declarations of Conformity and Regulatory Information A P P E N D I X BAutonomous Access Point Models Lightweight Access Point ModelsTested To Comply With FCC Standards FOR HOME OR OFFICE USE FCC Certification numbersVCCI Statement for Japan Industry Canada European Community, Switzerland, Norway, Iceland, and LiechtensteinCanadian Compliance Statement Autonomous Access Point ModelsEuropean Community, Switzerland, Norway, Iceland, and Liechtenstein Page Declaration of Conformity for RF Exposure Guidelines for Operating Cisco Aironet Access Points in Japan Japanese Translation English TranslationAutonomous Access Point Models Lightweight Access Point ModelsAdministrative Rules for Cisco Aironet Access Points in Taiwan Access Points with IEEE 802.11a RadiosChinese Translation English Translation Cisco Aironet 1130AG Series Access Point Hardware Installation GuideChinese Translation English Translation All Access PointsB-10 Declaration of Conformity Statements Declaration of Conformity Statements for European Union CountriesCisco Aironet 1130AG Series Access Point Hardware Installation Guide B-11Director Corporate Compliance Cisco Systems IncCisco Aironet 1130AG Series IEEE802.11 a/b/g Access Point Health & SafetyAnnex to DofC# 1. Information on Antennas and Power Levels Max Power LevelB-13 Antenna P/NCisco Aironet 1130AG Series Access Point Hardware Installation Guide B-14Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity StatementsAccess Point Specifications 802.11a Radio SpecificationsA P P E N D I X C Category802.11a Radio Specifications Access Point Specifications continuedCategory 802.11b Operation802.11a Radio Specifications Category802.11b Operation 802.11g OperationCisco Aironet 1130AG Series Access Point Hardware Installation Guide Appendix C Access Point SpecificationsOL-8369-05 Channels and Maximum Power Levels A P P E N D I X DCisco Aironet 1130AG Series Access Point Hardware Installation Guide Appendix D Channels and Maximum Power LevelsOL-8369-05 Console Cable Pinouts Cisco Aironet 1130AG Series Access Point Hardware Installation GuideA P P E N D I X E OL-8369-05Console Port Signals and Pinouts OverviewPins SignalsPriming Lightweight Access Points Prior to Deployment A P P E N D I X FPage Page Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Appendix F Priming Lightweight Access Points Prior to DeploymentOL-8369-05 Configuring DHCP Option 43 for Lightweight Access PointsA P P E N D I X G Overview Access PointVendor Class Identifier VCI Configuring Option 43 for 1000 and 1500 Series Access Points Type + Length + Value LAN Controller to operate G L O S S A R YGL-1 GL-2 A device that connects two otherwise incompatible networks together GL-3GL-4 GL-5 GL-6 I N D E access point imageextended temperature range 2-3 antenna connectorsIN-2