Manuals / Brands / Computer Equipment / Network Router / Cisco Systems / Computer Equipment / Network Router

Cisco Systems 1760 Attaching Brackets to the Rack, Attaching the Optional Cable Guide

1 40

Download 40 pages, 1.46 Mb

5

Attaching Brackets to the Rack

After the brackets are attached to the router, use the four supplied number-12 Phillips machine screws to securely attach the

brackets to the rack, as shown in Figure 3.

Caution Make sure that the fans on the side of the chassis are not blocked.

Figure3 Attaching Brackets to the Rack

Attaching the Optional Cable Guide

Cisco recommends attaching the cable guide to prevent the cables from obscuring the front panel of the router and the other

devices installed in the rack. If the router is in a 19-inch or 24-inch rack, use the supplied black screw, as shown in Figure 4, to

attach the cable guide to the left or right bracket.

PVDM 0

PWR1

SLOT 0

PVDM 1

MOD

SLOT 1

Phillips

truss-head

screws

24" Configuration

60943

Cisco 1700

Series

10/100 ETHERNET AUX

CONSOLE

PVDM 0

PWR 1

SLOT 0

PVDM 1

MOD

SLOT 1

LINK

100

FDX

ACT COL 1

SLOT 2

SLOT 3

60941

Phillips machine screws

Contents

Main Quick Start Guide Cisco 1760 Modular Access Router Cabling and Installation INCLUDING LICENSE AND WARRANTY 1 2 Product Serial Number Location 3 4 Attaching Brackets to the Router 5 Attaching Brackets to the Rack Phillips machine screws Figure3 Attaching Brackets to the Rack Attaching the Optional Cable Guide Phillips truss-head screws 5 Safety Information 7 Card Installation Figure5 Removing a WIC or VIC Slot Cover Figure6 Inserting a WIC or VIC in the Router 1 Interface Card 2 Cisco 1700 6 1 2 3 16 15 13 9 814 12 11 7 6 10 4 5 7 Read the following warnings before connecting the power to the router. 1 10/100 Ethernet port 3 2 Page 8 1 Blue console port 3 2 9 Initial Configuration Using Cisco Router and Security Device Manager Initial Configuration Using Cisco CLIManual Configuration Verifying the Initial Configuration 10 Information for International Users Saving the Configuration Configuring the Fast Ethernet Interface Configuring a Dial Plan Command Purpose Wildcards and Number Expansion Configuring Voice Interface Cards Destination Pattern Num-Exp Command Entry Description Configuring FXS Interfaces Local Dial Peers Telephone Number Voice Port Telephone Number Voice Port Dial-Peer Tag Page Checking the Local Dial Peer Configuration Calling Between Routers Telephone Number Destination Pattern Voice Port Dial-Peer Tag Remote Location Telephone Number Destination Pattern IP Address Dial-Peer Tag Other Routers on the Network Remote Location Telephone Number IP Address Dial-Peer Tag Checking the Remote Dial Peer Configuration Configuring FXO Interfaces Checking the FXO Configuration Configuring E&M Interfaces Command Task Page Checking the E&M Configuration Configuring ISDN BRI NT/TE Interfaces Configuring the BRI Layer 1 Configuring the ISDN Protocol Turning the Line Power On/Off Setting the Network Clock Priority Configuration Example Command Description Debugging Commands Configuring DID Interfaces Number Dialed by User A Number Received by Router Extension Receiving Call Prerequisites Configuring a Voice Port to Support DID Verifying DID Voice Port Configuration Configuring Quality of Service IP Precedence Low Latency Queuing Configuring LLQ Multilink PPP with Link Fragmentation Interleave Configuring MLPPP with LFI Real-Time Transport Protocol Header Compression Configuring RTP Header Compression Frame Relay Configuration for VoIP 11 Cisco.com Documentation DVD Ordering Documentation 12 13 Reporting Security Problems in Cisco Products 14 Cisco Technical Support Website Submitting a Service Request Definitions of Service Request Severity 15 Page Page Cisco Web site at www.cisco.com/go/offices