Cisco Systems N6KC600164P, N7KC7004, N7KC7004S2, N7KC7018RF, N7KF248XP25E, N7KF248XT25E, N7KF248XT25EP1, UCSCPCIECSC02, 7000 - page 65

Send document comments to nexus7k-docfeedback@cisco.com

3-15

Cisco Nexus 7000 Series Hardware Installation and Reference Guide

OL-18634-01

Chapter 3 Installing a Cisco Nexus 7018 Chassis

Installing the Cable Management Assemblies

Figure 3-8 Attaching the Lower Left Cable Management Assembly to the Left Rack-Mount

Bracket

Step 2 Attach an upper cable management assembly (800-31342-01) onto the two hooks t hat protrude from the

upper half of the left rack-mount bracket that is attached to the Cisco Nexus 7018 device chassis, and

loosely fasten the assembly to the chassis with four flat-head M4x1 0 screws as shown in Figure 3-9.

1Lower cable management assembly 2Left rack-mount bracket

3Position the assembly so that the two lower

hooks on the rack-mount bracket fit inside the

two holes on the assembly, and then slide the

assembly down so that it is held by the hooks.

4Loosely fasten the assembly to the

rack-mount bracket with four M4x10 screws.

Do not tighten these screws.

1

2

43

3

192181

Contents

Main Cisco Nexus 7000 Series Hardware Installation and Reference Guide Page CONTENTS Page Page Page Send document comments to nexus7k-docfeedback@cisco.com Page Preface Audience Organization Document Conventions xi This document uses the following conventions: publication. damage or loss of data. xii xiii xiv Page Related Documentation Release Notes Hardware Documents Software Documents Obtaining Documentation and Submitting a Service Request Page Overview Cisco Nexus 7000 Series Cisco Nexus 7010 System 234 5 5 8 6 7 Page Page Page Cisco Nexus 7018 System 12 2 58 Page Page Page Page Preparing the Site Safety Guidelines Installation and Connection Guidelines Managing the System Hardware Replacing Components Installing a Cisco Nexus 7010 Chassis Preparing to Install the Device Installing a Four-Post Rack or Cabinet Unpacking and Inspecting a New Device Installing the Bottom-Support Rails on the Rack Prerequisites for Attaching the Bottom-Support Rails Attaching the Bottom-Support Rails Page Page Installing the Chassis Prerequisites for Installing the Chassis Installing the Chassis Page Grounding the Cisco Nexus 7010 Chassis Prerequisites for Grounding the Chassis Connecting the System Ground Page Connecting Your ESD Strap to the Chassis 2-15 Figure 2-8 ESD Grounding Ports on the Front of the Cisco Nexus 7010 Chassis Installing and Formatting CompactFlash Cards Page Page Installing a Cisco Nexus 7018 Chassis Preparing to Install the Device Installing a Four-Post Rack or Cabinet Unpacking and Inspecting a New Chassis Installing the Bottom-Support Rails on the Rack Prerequisites for Attaching the Bottom-Support Rails Attaching the Bottom-Support Rails Page Installing the Chassis Prerequisites for Installing the Chassis Installing the Chassis Page Page Grounding the Cisco Nexus 7018 Chassis Prerequisites for Grounding the Chassis Connecting the System Ground Connecting Your ESD Strap to the Chassis Installing the Cable Management Assemblies Page Page 2 2 11 Page Installing the Front Door and Air Intake Frame Page Page Page 2 2 Page Page Page Page Page Installing and Formatting CompactFlash Cards Page Installing Power Supply Units Installing Power Supply Units Connecting the Power Supply Units to AC Power Prerequisites for Connecting Power Supply Units to AC Power Connecting 6-kW Power Supply Units Connecting 7.5-kW Power Supply Units Page Connecting the Cisco Nexus 7000 Device to the Network Preparing for Connections Required Tools and Equipment Connecting to the Console Creating an Initial Device Configuration Setting Up the Management Interface Connecting the Supervisor CMP Port Connecting an I/O Module Connecting or Disconnecting a 1000Base-T Port Connecting a 1000Base-T Port to the Network Disconnecting a 1000Base-T Port From the Network Connecting or Disconnecting an SFP or SFP+ Port Installing a Transceiver Removing a Transceiver Connecting a Fiber-Optic Cable with a Transceiver Disconnecting a Fiber-Optic Cable From a Transceiver Maintaining Transceivers and Fiber-Optic Cables Page Managing the Device Hardware Displaying the Device Hardware Inventory 6-2 Example 6-1 Displaying the Hardware Inventory To display switch hardware inventory details, enter the show hardware command. See Example 6-2. Example 6-2 Displaying Hardware Information 6-3 6-4 6-5 Displaying the Device Serial Number 6-6 Example 6-3 Displaying the Device Serial Number 6-7 Displaying Power Usage Information whether one or both supervisor modules are present. Example 6-4 Displaying Power Management Information Power Supply Configuration Modes Power Supply Configuration Overview Page Page Power Supply Configuration Guidelines Page Page Information About Modules Supervisor Modules I/O Modules Fabric Modules Verifying the Status of a Module Checking the State of a Module Connecting to a Module Shutting Down Modules Shutting Down a Supervisor or I/O Module Shutting Down a Fabric Module Information About Module Temperature Overview of Module Temperatures 6-19 Note A threshold value of 127 indicates that no thresholds are configu red or applicable. Displaying Module Temperature Example 6-6 Displaying Temperature Information for Hardware 6-20 Displaying Environment Information Example 6-7 Displaying All Environmental Information 6-21 Reloading Modules Reloading the Device, page 6-22 Power Cycling Modules, page 6-22 Reloading the Device Power Cycling Modules Saving the Module Configuration Purging the Module Configuration Powering Off I/O Modules Information About Fan Trays EPLD Configuration System Requirements Supported Device Hardware Supported Device Operating Systems Updated EPLDs Page Installation Guidelines Downloading the EPLD Images Preparing the EPLD Images for Installation 6-30 Example 10 Determining the Amount of Available Bootflash Memory Example 11 Determining the Amount of Available Slot0 Memory Upgrading EPLD Images Upgrading the EPLD Images for I/O or Standby Supervisor Modules 6-33 Step 2 Install the EPLDs by entering the install module slot_number epld url command. To reset the entire system, power cycle the system. Step 3 Begin upgrading the EPLD images by entering Y for yes. reset requirement. Upgrading EPLDs for the Active Supervisor Module Upgrading EPLDs for a Fabric Module Upgrading EPLDs for a Fan Tray Module Displaying the EPLD Versions Displaying EPLD Versions for an I/O or Supervisor Module 6-38 Example 14 Displaying the Current EPLD Versions for a Module Displaying EPLD Versions for a Fabric Module Example 15 Displaying the Current EPLD Versions for a Fabric Module Displaying EPLD Versions for a Fan Tray Module Example 16 Displaying Current EPLD Versions for Fan Tray 1 Displaying the Available EPLD Versions Default Settings Table 6-12 lists the default hardware settings. Tab l e 6-12 Default Hardware Parameters Parameters Default Power supply mode Power supply redundancy mode Page Troubleshooting Getting Started Troubleshooting the Power Supply Troubleshooting the Fan Trays Troubleshooting the Supervisor Modules Troubleshooting the Fabric Modules Troubleshooting the I/O Modules Contacting Customer Service Removal and Installation Procedures Replacing a Power Supply Unit During Operations Removing a Power Supply Unit During Operations Installing a Power Supply Unit During Operations Page Replacing a Supervisor Module Replacing One of Two Supervisor Modules During System Operations Page Page Replacing a Supervisor Module in a Single-Supervisor System Replacing an I/O Module Replacing an I/O Module Page Replacing a Fabric Module During System Operations Replacing a Fabric Module Page Replacing a Cisco Nexus 7010 System Fan Tray During System Operations Replacing a Cisco Nexus 7010 System Fan Tray Replacing a Cisco Nexus 7010 Fabric Fan Tray Replacing a Cisco Nexus 7010 Fabric Fan Tray Replacing a CompactFlash Card Page Installing the Front Doors and Frame Assembly Page Page Replacing the Cisco Nexus 7010 System Air Filter Page Page A Technical Specifications Environmental Specifications for the Cisco Nexus 7000 Series Systems Physical Specifications for the Cisco Nexus 7000 Series Devices Power Specifications for the Cisco Nexus 7000 Series Devices Power Requirements for Device Components Power Supply Configuration Modes Page Page Power Supply Cable Specifications A-8 Figure A-2 CAB-AC-16A-CH Power Cord and Connectors for the 6-kW Power Supply Unit Figure A-3 CAB-AC-2500W-EU Power Cord and Connectors for the 6-kW Power Supply Unit Figure A-4 CAB-AC-2500W-INT Power Cord and Connectors for the 6-kW Power Supply Unit A-9 Figure A-5 CAB-AC-2500W-ISRL Power Cord and Connectors for the 6-kW Power Supply Unit Figure A-6 CAB-AC-2500W-US1 Power Cord and Connectors for the 6-kW Power Supply Unit Figure A-7 CAB-AC-C6K-TWLK Power Cord and Connectors for the 6-kW Power Supply Unit A-10 Figure A-8 CAB-7513AC Power Cord and Connectors for the 6-kW Power Supply Unit Figure A-9 CAB-C19-CBN Power Cord and Connectors for the 6-kW Power Supply Unit Figure A-10 CAB-ACS-16 Power Cord and Connectors for the 6-kW Power Supply Unit Tab l e A-10 7.5 kW Power Supply AC Power Cords Chassis Clearances Facility Cooling Requirements Chassis Airflow Page Page B Cable and Port Specifications Module Connectors RJ-45 Connector SFP+ Transceivers SFP Transceivers Page Page C Chassis and Module LEDs Page Page Page Page Page D Repacking the Cisco Nexus 7000 Series Device for Shipment Disconnecting the Cisco Nexus 7000 Series System Powering Down the Cisco Nexus 7000 Series System Disconnecting the System from the Console Repacking the System Components Prerequisites for Repacking the System Required Tools and Equipment for Repacking the System Repacking the Cisco Nexus 7010 Device Page Page Page Page Page E Site Preparation and Maintenance Records Site Preparation Checklist Contact and Site Information Chassis and Module Information Page INDEX Numerics A B C D E F G H I L M N O P S T