Chapter 3 Provisioning the Cisco HSI
Cisco HSI Configuration
Table 3-3 Static System Data Parameters
| Parameter | Type | Description |
| |||
|
|
|
|
| |||
| HOST_PORT_NUMBER1 | The first port number to be used by the Cisco HSI. The default value is 0. | |||||
|
|
| Note This value must match the peer port setting on the PGW1 2200 | ||||
|
|
| |||||
|
|
|
|
| |||
| HOST_PORT_NUMBER2 | The second port number to be used by the Cisco HSI. The default value is 0. | |||||
|
|
| Note This value should always be set to 0. | ||||
|
|
|
|
| |||
| VSCA_IPADDR1 | STRING | The primary IP address of the primary PGW 2200. | ||||
|
|
|
|
| |||
| VSCA_IPADDR2 | STRING | The secondary IP address of the primary PGW 2200. | ||||
|
|
| Note This value must match that of VSCA_IPADDR1. | ||||
|
|
|
|
| |||
| VSCB_IPADDR1 | STRING | The primary IP address of the secondary PGW 2200. | ||||
|
|
| Note This parameter is not used in a standalone PGW configuration. | ||||
|
|
|
|
| |||
| VSCB_IPADDR2 | STRING | The secondary IP address of the secondary PGW 2200. | ||||
|
|
| Note The value of this parameter must match that of VSCB_IPADDR1. | ||||
|
|
| This parameter is not used in a standalone PGW configuration. | ||||
|
|
|
|
| |||
| VSCA_PORT_NUMBER1 | The first port number of the primary PGW 2200. | |||||
|
|
|
|
| |||
| VSCA_PORT_NUMBER2 | The second port number of the primary PGW 2200. | |||||
|
|
| Note This value must match that of VSCA_PORT_NUMBER1. | ||||
|
|
|
|
| |||
| VSCB_PORT_NUMBER1 | The first port number of the secondary PGW 2200. | |||||
|
|
| Note This parameter is not used in a standalone PGW configuration. | ||||
|
|
|
|
| |||
| VSCB_PORT_NUMBER2 | The second port number of the secondary PGW 2200. | |||||
|
|
| Note The value of this parameter must match that of | ||||
|
|
| VSCA_PORT_NUMBER2. This parameter is not used in a | ||||
|
|
| standalone PGW configuration. | ||||
|
|
|
|
| |||
| ClipClirSupported | STRING | CLI Presentation or restriction is enabled if this parameter is present and set to | ||||
|
|
| anything other than “”. For example, to enable CLIP/CLIR support, set this | ||||
|
|
| parameter explicitly to “Enabled.” | ||||
|
|
|
|
| |||
| RaiSupported | STRING | RAI support is enabled if this parameter is present and set to anything other than | ||||
|
|
| “”. For example, to enable RAI support, set this parameter to “Enabled.” | ||||
|
|
|
|
| |||
| DtmfSupportedDirection | STRING | This is set to “both”, “tx,” or “rx”. If this parameter is not present or is set to any | ||||
|
|
| value other than “both,” “tx,” or “rx,” the DTMF Relay feature is disabled. | ||||
|
|
|
|
| |||
| DtmfSupportedType | STRING | This is set to “dtmf” or “basicString.” If this parameter is not present or set to | ||||
|
|
| any other value, the DTMF Relay feature is disabled. | ||||
|
|
|
|
| |||
| H225PavoSupported | STRING | Pavo support is enabled if this parameter is present and set to anything other than | ||||
|
|
| “”. For example, set it to “Enabled.” | ||||
|
|
|
|
| |||
| PavoRedirScreeningInd | The value of the Pavo redirecting number screening indicator. (If this parameter | |||||
|
|
| is not provisioned, the default is Q.931 | ||||
|
|
|
|
| |||
| PavoRedirReason | The value of the Pavo redirecting number reason field. This parameter has no | |||||
|
|
| default. If unprovisioned, the redirecting number parameter will not contain the | ||||
|
|
| Reason for Redirection field (octet 3b). | ||||
|
|
|
|
|
|
| |
|
|
| Cisco H.323 Signaling Interface User Guide |
|
|
| |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|