Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems H.323 appendix 3-19, Parameter Name, Parameter Value, Description, Example

Models: H.323

1 32

Download 32 pages 39.25 Kb

Page 19

Image 19

Chapter 3 Provisioning the Cisco HSI

H.323 Stack Configuration

Table 3-13 Common Call Control Parameters (continued)

Parameter Name	Parameter Value	Description

A_CC_Interworking	0—No interworking encountered (SS7 all	Backward call indicator, Interworking indicator
	the way)
	1—Interworking encountered

A_CC_Location	1—User	Cause indicator, Location
	2—Private local
	3—Public local
	4—Transit
	5—Public remote
	6—Private remote
	7—International
	8—Interworking
	9—Local interface
	11—Local remote
	12—Packet manager
	13—Unknown

The following MML command example shows the command sequence used to provision the call control parameters provided in the preceding table.

Example

mml

>prov-sta::srcver=active, dstver=myconf

>prov-ed:name=CCPackage, A_CC_ANumDataSI=2

>prov-cpy

>restart-softw

Table 3-14presents important static system data parameters.

	Cisco H.323 Signaling Interface User Guide
	Cisco H.323 Signaling Interface User Guide
OL-4806-01 Rev. A14		3-19
OL-4806-01 Rev. A14		3-19

Page 19

Image 19

Cisco Systems H.323 appendix 3-19, Parameter Name, Parameter Value, Description, Example

Contents

Introduction Cisco HSI ConfigurationCisco HSI Configuration, page H.323 Stack Configuration, page HSI Feature Configuration, pageDescription MML Configuration CommandsCommand prov-sta prov-cpy prov-stpInitiating an MML Session to Enable DTMF on the HSI Introduction to MML Command Operation for HSIVerifying the Configuration Example System Configuration DataReverting to the Base Configuration Static System DataTable 3-3 Static System Data Parameters ParameterType DescriptionTable 3-3 Static System Data Parameters continued ParameterType DescriptionType Step 3 Issue the command restart-softwconfirmChanging Static System Data ParameterExample DefaultDynamic System Data “Logging Levels” section on pageTable 3-4 Dynamic System Data Parameters continued DefaultParameter DescriptionParameter H.323 Stack Configuration3-10 DefaultH.323 System Parameters prov-dlt, and prov-ed commandsNonprovisionable Data MML Provisionable DataExample Update TypeParameter Name 3-12Parameter Name RAS Parameters3-13 ExampleType 3-14Parameter Name DescriptionDescription H.245 Parameters3-15 Parameter NameDescription Update3-16 Parameter NameParameter Name 3-17Parameter Name Type3-18 Codec SelectionQuick Reference for Important Parameters Parameter ValueDescription 3-19Parameter Name Parameter ValueDescription Parameter Values3-20 Parameter NameParameter Values See Table3-21 Parameter NameT.38 Fax HSI INFORMATION Message Support HSI Feature ConfigurationConfiguring Clear Channel on the Cisco HSI Asymmetric Codec Treatment Empty Capability Set H.323 HairpinEmpty Capability Set Configuring G.726 on the Cisco HSIConfiguring G.729 Annex and G.729 Annex B Asymmetric Codec TreatmentT.38 Fax Configuring T.38 Fax on the Cisco PSTN GatewayConfiguring T.38 Fax on a Cisco IOS H.323 Gateway Configuring T.38 Fax on a Cisco IOS MGCP GatewayHSI Support for Tech Prefixes Configuring Clear Channel on the Cisco HSI3-25 3-26 Example ConfigurationClear Channel Parameters Example Value3-27 Configuring G.726 on the Cisco HSIG.726 Parameter Configuration ExampleConfiguring the Payload Type for the MGCP Configuring Cisco HSI g726-ciscoG.726 Parameter Configuring Cisco HSI g726-generic3-29 Configuration ExampleExample Value 3-30Configuration Example G.726 ParameterConfiguration Example Configuring G.729 Annex and G.729 Annex BG.729 Parameter 3-31G.729 Parameter 3-32Example Configuration Table 3-19 Configuring G.729 Annex A and G.729 Annex B continued