Cisco Systems PA-2FE-FX, PA-2FE-TX Cisco 7201 Router-Removing and Installing a Port Adapter, Step

Models: PA-2FE-FX PA-2FE-TX

1 82
Download 82 pages 10 b
Page 51
Image 51
Cisco 7201 Router—Removing and Installing a Port Adapter

Chapter 3 Removing and Installing Port Adapters

Port Adapter Removal and Installation

Cisco 7201 Router—Removing and Installing a Port Adapter

Step 1

Use an ESD wrist strap to ground yourself to the router.

Step 2

To remove the port adapter, place the port adapter lever in the unlocked position. The port adapter lever remains in the unlocked position.

Step 3

Grasp the handle of the port adapter and pull the port adapter about halfway out of its slot. If you are removing a blank port adapter, pull the blank port adapter completely out of the chassis slot.

Step 4

With the port adapter halfway out of the slot, disconnect all cables from the port adapter.

After disconnecting the cables, pull the port adapter from the chassis slot.

Caution

The port adapter must slide into the slot guides close to the chassis lid. Do not allow the port adapter components to come in contact with the system board or the port adapter could be damaged.

 

 

 

 

 

E

 

 

 

 

 

 

 

 

 

 

ENABLEDRX

RX

XA

 

Cisco 7201

 

E

 

 

R

 

 

 

 

 

 

S

IER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CELL

CARR LARM

 

 

 

 

 

 

 

G

N

 

 

 

 

 

 

R

RJ45

EN

LINK/ACTV

 

 

 

X

 

 

CONSOLE

 

 

 

 

 

ATM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SFP

RJ45

EN

LINK/ACTV

 

 

 

 

 

 

 

 

 

 

 

 

 

TX

SFP

RX

LINK/ACTV

LINK/ACTV

 

 

 

 

 

 

 

 

 

 

 

 

SFP

 

 

 

 

 

 

 

 

GE 0/0

 

 

 

 

TX

SFP

RX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MNGMNT USE ONLY

 

 

 

 

 

 

 

 

 

GE 0/1

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

 

 

 

GE 0/2

GE 0/3

 

 

 

ALARM

 

 

 

 

 

 

 

 

 

 

 

 

AUX

 

 

PWR OK

 

 

 

 

 

 

 

 

 

 

 

 

FE 0/0

FE

0

 

 

 

 

 

 

 

 

 

 

 

 

 

LINK

COMPACT

STATUS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FLASH

CF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ACTV

Step 5

To insert the port adapter, carefully align the port adapter carrier in the slot guides. Slide the new port adapter halfway into the chassis.

170902

Step 6

Connect all the required cables to the port adapter. After connecting all required cables, carefully slide the port adapter all the way into the slot until the port adapter is seated in the midplane.

Step 7

After the port adapter is properly seated, lock the port adapter lever.

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

 

OL-3474-07

3-9

 

 

 

Page 51
Image 51
Cisco Systems PA-2FE-FX, PA-2FE-TX manual Cisco 7201 Router-Removing and Installing a Port Adapter, Step