Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems PA-2FE-TX, PA-2FE-FX manual 3-14, Remove a module as follows

Models: PA-2FE-FX PA-2FE-TX

1 82

Download 82 pages 10 b

Page 56

Remove a module as follows:

Chapter 3 Removing and Installing Port Adapters

Port Adapter Removal and Installation

Removing and Installing a VIP Carrier Card in the Cisco 7500 Series Router

Remove a module as follows:

1.Use a screwdriver to loosen the captive installation screws (shown in A and D).

2.Simultaneously pull the ejector levers out to release the module from the backplane connector (shown in B). The levers should snap into their spring retainers.

3.Grasp the module handle with one hand and place your other hand under the carrier to support and guide the module as you pull it out of the slot. Avoid touching the card.

4.Place the removed module on an antistatic mat or antistatic foam, or immediately install it in another slot.

5.Install a new module or a filler (MAS7K- BLANK) to keep dust out of the chassis and to maintain proper airflow through the chassis.

Install a module as follows:

1.Choose a slot for the new module and ensure that there is enough clearance to accommodate any interface equipment that you will connect directly to its ports.

2.Use a screwdriver to loosen the captive installation screws (shown in A) and remove the filler (or the existing module) from the slot to be filled.

3.Hold the module handle with one hand, and place your other hand under the carrier to support the module and guide it into the slot. Avoid touching the card.

4.Place the back of the module in the slot and align the guide on the carrier with the groove in the slot (shown in A).

5.Carefully slide the module into the slot until the faceplate makes contact with the ejector levers (shown in C).

6.Use the thumb and forefinger of each hand to push the ejector lever flat against the module (shown in B).

7.Use a screwdriver to tighten the captive installation screws.

Card carrier guide

A

Captive installation screw

B

C

D

Captive installation screw

LT

ROUTE SWITCH PROCESSOR

T

H

A

T

JE

C

1

PU

E

AL

E

LO

T

C

R

ES

X.

E

M

S

T

0

A

U

ON

S

OL

NO

R

S

LO

C

39395

PA-2FE-TX and PA-2FE-FX Two-Port Fast Ethernet Port Adapter Installation and Configuration

3-14	OL-3474-07

Image 56

Cisco Systems PA-2FE-TX, PA-2FE-FX manual 3-14, Remove a module as follows

Contents

Americas Headquarters Ethernet Port Adapter Installation and ConfigurationPA-2FE-TX and PA-2FE-FX Two-Port Fast Turn the television or radio antenna until the interference stops Preface ObjectivesLEDs Cisco 7304 PCI Port Adapter Carrier Card Slot NumberingConfiguring the PA-2FE Safety WarningsSafety Guidelines Telephone Wiring GuidelinesUsing the show diag Command Using the show interfaces CommandContents 4-21Contents OL-3474-07Preface Document Revision HistoryDocument Revision History, page Objectives, page Organization, page Related Documentation, pagePreparing for Installation Removing and InstallingConfiguring the PA-2FE ObjectivesCisco 7100 series routers Regulatory Compliance and Safety Information for Cisco 7100 Series VPN Routers Obtaining Documentation, Obtaining Support, and Security Guidelines OL-3474-07 PrefaceObtaining Documentation, Obtaining Support, and Security Guidelines IEEE 802.3u 100BASE-T Specifications, page LEDs, page OverviewPort Adapter Overview C H A P T E RIEEE 802.3u 100BASE-T Specifications Fast Ethernet OverviewParameter 100BASE-TXCabling Specifications continued 10,000 m FX-single mode DTE DTE Maximum segment length, half duplexMaximum segment length, full duplex 100 m TX DTE* DTE 2000 m FX-multimode Maximum segment length, full duplexLEDs Receptacles, Cables, and PinoutsLED Label Color1 RJ-45 connector and port Network Management Port Adapter Slot Locations on the Supported Platforms Cisco 7100 Series Routers Slot NumberingCisco 7100 Series Routers Slot Numbering, page Cisco uBR7200 Series Router Slot Numbering, pageFigure 1-12 Port Adapter Slots in the Cisco 7206 Router Cisco 7200 Series Routers and Cisco 7200 VXR Routers Slot NumberingFigure 1-11 Port Adapter Slots in the Cisco 7140 Series Router Cisco uBR7200 Series Router Slot Numbering Figure 1-13 Port Adapter Slots in the Cisco uBR7246VXR RouterCisco 7201 Router Slot Numbering Cisco 7301 Router Slot Numbering1-10 Port adapter slotFigure 1-16 Module Slots on the Cisco 7304 Router Cisco 7304 PCI Port Adapter Carrier Card Slot Numbering1-11 Cisco 7401ASR Router Slot Numbering Cisco 7500 Series Routers with VIP Slot Numbering1-12 Figure 1-18 Port Adapter Slot in the Cisco 7401ASR RouterFigure 1-20 VIP Slots in the Cisco 7505 Router 1-13ROUTE SWITCH PROCESSOR 1-14 RESETFigure 1-21 VIP Slots in the Cisco 7507 Router EJECTFigure 1-22 VIP Slots in the Cisco 7513 Router 1 3 5 7 9 111-15 Identifying Interface Addresses Cisco 7120 Router and Cisco 7140 Router Interface Addresses, pageCisco uBR7200 Series Routers Interface Addresses, page Cisco 7201 Router Interface Addresses, pageIdentifying Interface Addresses continued Cisco 7120 Router and Cisco 7140 Router Interface Addresses1-17 Cisco uBR7200 Series Routers Interface Addresses Cisco 7201 Router Interface AddressesCisco 7301 Router Interface Addresses Cisco 7304 PCI Port Adapter Carrier Card Interface AddressesCisco 7500 Series Routers VIP Interface Addresses 1-19OL-3474-07 1-20Chapter 1 Overview Identifying Interface Addresses Preparing for Installation Safety Guidelines, page FCC Class A Compliance, pageRequired Tools and Equipment Required Tools and Equipment, pageSoftware and Hardware Requirements Checking Hardware and Software Compatibilityrouters VXR routers1Warning Definition Safety GuidelinesSafety Warnings Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ CONSERVEZ CES INFORMATIONS Warnung WICHTIGE SICHERHEITSHINWEISEBEWAHREN SIE DIESE HINWEISE GUT AUF Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo Chapter 2 Preparing for Installation Safety Guidelines OL-3474-07Electrical Equipment Guidelines Telephone Wiring Guidelines Preventing Electrostatic Discharge DamageFCC Class A Compliance 2-10Removing and Installing Port Adapters Port Adapter Removal and Installation, pageConnecting a PA-2FE RJ-45 or SC Cable, page Handling Port AdaptersOnline Insertion and Removal Figure 3-1 Handling a Port AdapterWarnings and Cautions Port Adapter Removal and Installation Cisco 7100 Series-Removing and Installing a Port Adapter, pageCisco uBR7200 Series Routers-Installing a Port Adapter, page Cisco 7201 Router-Removing and Installing a Port Adapter, pageCisco 7100 Series-Removing and Installing a Port Adapter StepStep StepStep StepStep StepCisco uBR7200 Series Routers-Removing a Port Adapter StepStep StepCisco uBR7200 Series Routers-Installing a Port Adapter StepStep StepCisco 7201 Router-Removing and Installing a Port Adapter StepStep StepCisco 7301 Router-Removing and Installing a Port Adapter A B C3-10 Step3-11 3-12 Chapter 3 Removing and Installing Port AdaptersPort Adapter Removal and Installation CARRIERALARMCisco 7401ASR Router-Removing and Installing a Port Adapter Cisco 7500 Series Router VIP-Removing and Installing a Port Adapter3-13 Step3-14 Remove a module as followsRemoving and Installing the Port Adapter in the VIP Carrier Card 3-15Step StepConnecting a PA-2FE RJ-45 or SC Cable 3-163-17 Figure 3-4 Connecting PA-2FE-FX SC Cables-Horizontal OrientationChapter 3 Removing and Installing Port Adapters Connecting a PA-2FE RJ-45 or SC Cable3-18 Chapter 3 Removing and Installing Port AdaptersConnecting a PA-2FE RJ-45 or SC Cable OL-3474-07Configuring the PA-2FE Using the EXEC Command InterpreterUsing the EXEC Command Interpreter, page Configuring the Interfaces, page Checking the Configuration, pageConfiguring the Interfaces Performing a Basic Interface Configuration, pageShutting Down an Interface Shutting Down an Interface, pagefastethernet and slot/port shutdownfastethernet and slot/port shutdownfastethernet and slot/port shutdownfastethernet and slot/port shutdownshow interfaces fastethernet show interfaces fastethernetshow interfaces fastethernet show interfaces fastethernetshow interfaces fastethernet show interfaces fastethernetslot-number/port-number show interfaces fastethernetPerforming a Basic Interface Configuration fastethernet and slot/portfastethernet and slot/port fastethernet and slot/portfastethernet and fastethernet and slot/portfastethernet and slot/port fastethernet and slot/portChecking the Configuration Using show Commands to Verify the New Interface StatusUsing show Commands to Verify the New Interface Status, page Using the ping Command to Verify Network Connectivity, pageUsing the show version or show hardware Commands, page Using the show diag Command, pageUsing the show interfaces Command, page 4-10Using the show version or show hardware Commands Cisco 7100 Series Routers-Example Output of the show version CommandCisco 7201 Router-Example Output of the show version Command, page Cisco 7401ASR Router-Example Output of the show version Command, pageCisco 7201 Router-Example Output of the show version Command 4-12Cisco 7401ASR Router-Example Output of the show version Command 4-13Using the show diag Command Cisco 7201 Router-Example Output of the show diag Command, pageCisco 7401ASR Routers-Example Output of the show diag Command, page 4-14Cisco 7100 Series Routers-Example Output of the show diag Command 4-15Cisco 7201 Router-Example Output of the show diag Command 4-16Cisco 7401ASR Routers-Example Output of the show diag Command 4-174-18 Using the show interfaces CommandCisco 7201 Router-Example Output of the show interfaces Command, page 4-19 Cisco 7201 Router-Example Output of the show interfaces Command Cisco 7401ASR Router-Example Output of the show interfaces Command4-20 Router# show interfacesUsing the ping Command to Verify Network Connectivity 4-21OL-3474-07 4-22Chapter 4 Configuring the PA-2FE Checking the Configuration