Chapter 2 Switch Installation

Planning a StackPower Stack

•If some switches in the stack are completely separated from the stack, a stack split can take occur.

•A stack split can occur on a full ring stack if:

–More than one running switch is removed without powering down.

–More than one stack cable is removed without powering down.

•A stack split can occur in a partial ring stack if:

–A switch is removed without powering down.

–A stack cable is removed without powering down.

•In a split stack, depending on where the active and standby switches are located, either two stacks might be formed (with the standby taking over as the new active switch in the newly formed stack) or all the members in the newly formed stack might reload.

Note These results depend on how the switches are connected. You can remove two or more switches from the stack without splitting the stack.

For conditions that can cause a stack reelection or to manually elect the active switch, see the stacking software configuration guide on Cisco.com at this URL:

http://www.cisco.com/go/cat3850_docs

Planning a StackPower Stack

Catalyst 3850 switches can share power by using the StackPower feature.

•StackPower Stacking Guidelines, page 2-8

•StackPower Cabling Configurations, page 2-9

StackPower Stacking Guidelines

You can configure a StackPower stack for either power sharing or redundancy. In power-sharing mode, the power of all the power supplies in the stack is aggregated and distributed among the stack members.

In redundant mode, when the total power budget of the stack is calculated, the wattage of the largest power supply is not included. That power is held in reserve and used to maintain power to switches and attached devices when one power supply fails. Following the failure of a power supply, the StackPower mode becomes power sharing.

Note Power-sharing mode is the recommended configuration for Catalyst 3850 switches.

For general concepts and management procedures for switch power stacks, see the software stacking configuration guide on Cisco.com.

Before connecting the switches in a power stack, keep in mind these guidelines:

Catalyst 3850 Switch Hardware Installation Guide

2-8

OL-26779-02

 

 

Page 41 Page 43
Page 42
Image 42
Cisco Systems WSC385024TS, C3850NM210G, C3850NM41G manual Planning a StackPower Stack, StackPower Stacking Guidelines
Page 41 Page 43

C3850NM41G, C3850NM210G, WSC385024TS specifications

Cisco Systems is a global leader in networking and telecommunications hardware, and its Catalyst series of switches are widely recognized for their innovation, reliability, and performance. Among the numerous models available, the Cisco WSC385024TS, C3850NM41G, and C3850NM210G stand out for their advanced features and capabilities tailored to meet the needs of modern enterprises.

The Cisco WSC385024TS is a stackable switch that offers 24 ports, and it is built on Cisco's IOS XE software. It is designed for high-density environments, making it ideal for organizations that require robust connectivity and scalability. This model supports advanced Layer 2 and Layer 3 features and facilitates intelligent traffic management through Quality of Service (QoS). One of its standout features is the ability to stack up to nine switches together, enabling centralized management and increased fault tolerance. The WSC385024TS also integrates security features such as 802.1X authentication and access control lists, which are essential for maintaining a secure network infrastructure.

The C3850NM41G is a versatile switch that comes with 41 Gigabit Ethernet ports, making it suitable for environments that demand high-speed connectivity. This model supports Cisco's innovative StackWise-480 technology, which provides increased bandwidth and reliable inter-switch communication. Additionally, it features Power over Ethernet (PoE) capabilities, allowing it to deliver power to connected devices such as IP phones and wireless access points, thereby simplifying cabling and reducing the need for additional power sources. The C3850NM41G is also equipped with built-in automatic fault detection and recovery, enhancing the overall resilience of the network.

Lastly, the C3850NM210G model offers 210 Gbps of switching capacity, making it ideal for data-intensive applications. This switch combines performance with security, supporting various security protocols such as Virtual Routing and Forwarding (VRF) and Dynamic Host Configuration Protocol (DHCP) snooping to protect against malicious activity. With its modular design, the C3850NM210G allows for easy upgrades and expansions, facilitating adaptive network growth.

In summary, the Cisco WSC385024TS, C3850NM41G, and C3850NM210G switches provide advanced features, robust performance, and high scalability, making them ideal choices for businesses aiming to enhance their network infrastructure while supporting cutting-edge technologies. Whether for small businesses or large enterprises, these models exemplify Cisco's commitment to delivering high-quality networking solutions that adapt to the evolving demands of today's digital landscape.
Top Page Image Contents