Clarion VRX610 owner manual Basic Operations

8. OPERATIONS

Basic Operations

Basic Operations	Note: Be sure to read this chapter referring to the front diagrams of
	chapter “2. CONTROLS” on page 5 (unfold).

• If a title has been input, it is shown in the SUB dis-

play. If no title has been input, “---------” appears in

the display. To input a title, refer to the subsection

“Entering titles” in “Other Functions” section.

3.To store the Color LCD display ¥in the source unit, turn it to the horizontal position until a click is heard.

CAUTION

When the unit is turned on, starting and stop- ping the engine with its volume raised to the maximum level may harm your hearings. Be careful about adjusting the volume.

Note:

• Use this unit after starting the engine.

Adjusting the volume

Operate the VOLUME button 2 in the direction of the arrows w (up) or z (down) to adjust the volume;

w: Increases the volume.

z: Decreases the volume.

∗The volume level indicated in the display is in a range from 0 (minimum) to 33 (maximum).

• Some special characters of the title, will not be

displayed on the Information Panel of the DCP. In

this case, those characters will only be left blank.

Showing a mode display

When the panel is open:

Press the TITLE button ( to show the Title List display. In the Title List display, the titles of items stored in the PRESET buttons #1 to 6 are listed.

Turning on and off the power

Note:

• Be careful about using this unit for a long time with-

CAUTION

While driving, keep the volume at a level at which external sounds can be heard.

Switching the display

∗For detailed information, refer to the section “Title list play”.

Opening and turning the display

Notes:

•Do not place any object on the open display.

•Do not drop any object on the movable part.

•Do not expose the display to shocks.

Turning on and off the monitor

Pressing the DISP button @ turns the monitor on and off.

∗When a button is pressed or during security moni- toring, the monitor-off mode is canceled.

out running the engine. If you drain the car’s bat-

tery too far, you may not be able to start the en-

gine and this can reduce the service life of the

battery.

1.Press the POWER button 1.

2.The illumination and display on the unit light up. The unit automatically remembers its last operation mode and will automatically switch to display that mode.

3.Press and hold the POWER button 1for 1 sec- ond or longer to turn off the power for the unit.

Note:

•About the “SYSTEM CHECK”

The confirmation of connected equipment must be performed for this unit only when the wiring con- nection is complete and power is turned on to the unit first. When the power is supplied, “SYSTEM ”

and “PUSH PWR” appear alternately in the dis- play. Press the POWER button 1, the system

check starts inside the unit. When “COMPLETE” appears, press once again the POWER button 1.

Selecting a mode

1.Press the FUNC button 1to change the mode of operation.

2.Each time you press the FUNC button 1, the mode of operation changes in the following order:

Radio mode ➜ CD changer mode ➜ MD changer mode ➜ TV mode ➜ Radio mode...

∗External equipment not connected with CeNET is not selected.

When the panel is closed:

Press the DISP button @ to select the desired dis- play.

Each time you press the DISP button @, the dis- play switches in the following order:

Notes:

•Once selected, the preferred display becomes the default display. When a function adjustment such as volume is made, the display momentarily switches to that function’s display, then returns back to the preferred display several seconds af- ter the adjustment.

1.Press the OPEN button ! to open the Color LCD display ¥.

∗If the Color LCD display ¥ is left horizontally in the open position for 10 seconds or longer, it is automatically drawn in.

2.Turn the Color LCD display ¥ upwards to a good view angle.

When the monitor is turned upwards, a pic- ture appears in the display. The Information Panel 4 display disappears.

CAUTION

Do not turn the display unless it is completely open.

When adjusting the angle of the display be careful no to let your fingers get caught by the panel or instrument panel of the vehicle.

Mute

Each time you press the MUTE button $, mute is turned on and off.

“MUTE” appears when mute is turned on.

Setting the Z-enhancer

This unit comes with 3 types of sound tone effect stored in memory. Select the one you prefer.

∗The factory default setting is “Z-EHCR OFF”. When a Z-enhancer comes on (1-3),“Z-EHCR” appears in the display.

• “Z-EHCR 1” (Z-Enhancer 1):

Setting emphasizing bass.

• “Z-EHCR 2” (Z-Enhancer 2):

Setting emphasizing treble.

• “Z-EHCR 3” (Z-Enhancer 3):

Setting emphasizing bass and treble.

• “Z-EHCR OFF” (Z-Enhancer off):

Neither bass nor treble are empha- sized by the Z-enhancer.

Note:

•Incapable of operation when connecting DSP (DPH7500z/7700z).

16 VRX610 VRX610 17