Clarion XDZ716 owner manual Troubleshooting, Error Displays

9. TROUBLESHOOTING

	Problem	Cause	Measure
	Power does not	Fuse is blown.	Replace with a fuse of the same amperage. If the
	turn on.		fuse blows again, consult your store of purchase.
	(No sound is
		Incorrect wiring.	Consult your store of purchase.
	produced.)
	No sound output	Power antenna lead is	1. Turn the unit off.
	when operating	shorted to ground or	2. Remove all wires attached to the power antenna
	the unit with	excessive current is required	lead. Check each wire for a possible short to
	amplifiers or	for remote-on the amplifiers	ground using an ohm meter.
	power antenna	or power antenna.	3. Turn the unit back on.
	attached.		4. Reconnect each amplifier remote wire to the
			power antenna lead one by one. If the amplifiers
General			turn off before all wires are attached, use an
			external relay to provide remote-on voltage
			(excessive current required).
	Nothing happens	The microprocessor has	Turn off the power, then press the RELEAS button 1
	when buttons are	malfunctioned due to noise,	and remove the DCP.
	pressed.	etc.	Press the reset button for about 2 seconds with a thin
			rod.
	Display is not		Reset button
	accurate.

		DCP or source unit	Wipe the dirt off with a soft cloth moistened with
		connectors are dirty.	cleaning alcohol.
	Compact disc	Another compact disc is	Eject the compact disc before loading the new one.
	cannot be loaded.	already loaded.
	Sound skips or is	Compact disc is dirty.	Clean the compact disc with a soft cloth.
	noisy.
CD		Compact disc is heavily	Replace with a compact disc with no scratches.
		scratched or warped.
	Sound is bad	Water droplets may form on	Let dry for about 1 hour with the power on.
	directly after	the internal lens when the
	power is turned	car is parked in a humid
	on.	place.

10. ERROR DISPLAYS

If an error occurs, one of the following displays is displayed.

Take the measures described below to eliminate the problem.

Error Display	Cause	Measure
ERROR 2	A CD is caught inside the CD deck and is	This is a failure of CD deck’s mechanism
	not ejected.	and consult your store of purchase.

CD	ERROR 3	A CD cannot be played due to scratches,	Replace with a non-scratched,
		etc.	non-warped-disc.
	ERROR 6	A CD is loaded upside-down inside the CD	Eject the disc then reload it properly.
		deck and does not play.
	ERROR 2	A CD inside the CD changer is not loaded.	This is a failure of CD changer’s mecha-
changerCD			nism and consult your store of purchase.
	ERROR 6	A CD inside the CD changer cannot be	Eject the disc then reload it properly.
	ERROR 3	A CD inside the CD changer cannot be	Replace with a non-scratched, non-warped
		played due to scratches, etc.	disc.
		played because it is loaded upside-down.
	ERROR H	Displayed when the temperature in the	Lower the surrounding temperature and
		MD changer is too high and playback has	wait for a while to cool off MD changer.
		been stopped automatically.
changer	ERROR 2	An MD inside the MD changer is not	This is a failure of MD changer’s mecha-
		loaded.	nism and consult your store of purchase.
	ERROR 3	An MD inside the MD changer cannot be	Replace with a non-scratched, non-warped
MD		played due to scratches, etc.	disc.
	ERROR 6	An MD inside the MD changer cannot be	Eject the disc then reload it properly.
		played because it is loaded upside-down.
		Displayed when a non-recorded MD is	Load a pre-recorded MD in the MD
		loaded in the MD changer.	changer.

If an error display other than the ones described above appears, press the reset button. If the problem persists, turn off the power and consult your store of purchase.

32 XDZ716 XDZ716 33