CAUTION
Be sure to lower the volume before switch- ing off the unit power or the ignition key. The unit remembers its last volume setting. If you switch the power off with the volume up, when you switch the power back on, the sudden loud volume may hurt your hearing and dam- age the unit.
Turning on/off the power
Note:
•Be careful about using this unit for a long time with- out running the engine. If you drain the car’s bat- tery too far, you may not be able to start the en- gine and this can reduce the service life of the battery.
1. | Press POWER button 3. |
2. | The illumination and display on the unit light |
| up. The unit automatically remembers its last |
| operation mode and will automatically switch |
| to display that mode. |
3. | Press and hold POWER button 3 for 1 sec- |
Adjusting the volume
Turning the Rotary knob ( clockwise increases the volume; turning it counterclockwise de- creases the volume.
∗The volume level is from 0 (minimum) to 33 (maxi- mum).
Switching the display
Press DISP button # to select the desired dis- play.
Each time you press DISP button #, the display switches in the following order:
Main display
Clock (CT) display
∗The factory default setting is “USER CUSTOM”. Each time you press BEQ button 8, the tone effect changes in the following order:
“1 BASS BOOST” ➜ “2 IMPACT” ➜ “3 EXCITE”
➜“USER CUSTOM” ➜ “TONE BYPASS” ...
• 1 BASS BOOST : bass emphasized
• 2 IMPACT | : bass and treble emphasized |
• 3 EXCITE | : bass and treble emphasiaed |
| mid de emphasised |
•USER CUSTOM : user custom
•TONE BYPASS : no sound effect
Adjusting the tone
Press A-M button $ and select the item to ad- just. Each time you press A-M button $, the item changes in the following order:
●When the BEQ (BASS BOOST, IMPACT, EXCITE) is set
“NON-FAD VOL” ➜ “BASS BOOST” ( IMPACT, EXCITE) ➜ “BALANCE” ➜ “FADER” ➜ Function mode...
Adjusting the bass
The bass gain, bass F (center frequency) and bass Q can be adjusted as follows.
1.Press the A-M button $ and select “BASS 
GAIN ”.
2.Press the SEARCH button % and select from
“BASS 
GAIN
” ➜ “BASS 
F 50
” ➜ “BASS 
Q 1 ” ➜ “BASS 
GAIN ”.
3.Turn the Rotary knob ( clockwise or coun- terclockwise as needed and adjust the gain, the F (center frequency) and the Q.
BASS GAIN : –6 to 8 (The factory default setting is “0”)
BASS F : 50Hz/80Hz/120Hz (The fac- tory default setting is “50”)
BASS Q : 1/1.25/1.5/2 (The factory de- fault setting is “1”)
4.When the adjustment is complete, press A-M button $ several times until the function mode is reached.
ond or longer to turn off the power for the unit. |
Note:
•System check
The first time this unit is turned on after the wire connections are completed, it must be checked
what equipment is connected. When the power is turned on, “SYSTEM CHCK” 
“Push Power ” appears in the display, so press POWER button 3. The system check starts within the unit. When
the system check is complete, the power is turned off, so press POWER button 3 again.
Selecting a mode
1. | Press FNC button 3 to change the mode of |
| operation. |
2. | Each time you press FNC button 3, the mode |
Main display...
∗ | Once selected, the preferred display becomes |
| the display default. When a function adjustment |
| such as volume is made, the screen will mo- |
| mentarily switch to that function’s display, then |
| revert back to the preferred display several |
| seconds after the adjustment. |
∗ | When you have entered a title in a CD/MD, it |
| appears in the sub display. If you have not en- |
| tered a title, “D NO-TITLE” or “T NO-TITLE” |
| appears in the title display instead. For infor- |
●When the BEQ (USER CUSTOM) is set
“NON FAD VOL” ➜ “BASS” ➜ “MID” “TREBLE” ➜ “BALANCE” ➜ “FADER” ➜ Function mode…
●When the , BEQ is off
“NON-FAD VOL” ➜ “BALANCE” ➜ “FADER” ➜ Function mode…
∗Pressing the SBE button 8 for 1 second or longer while in “USER-CUSTOM” sets flat, and displays a “BEQ FLAT” message.
Note:
•When the separately-sold digital sound processor (DPH910) is used, the bass and treble tone adjust- ments cannot be selected. To adjust the tone, refer to the section “AC Proeesser Operations”.
Adjusting the MID
The MID gain, MID F (center frequency) and MID Q can be adjusted as follows.
1.Press the A-M button $ and select MID GAIN.
2.Press the SEARCH button % and select from
“MID 
GAIN ” ➜ “MID 
F 1k ” ➜ “MID 
Q 2 ” ➜ “MID 
GAIN ”.
3.Turn the Rotary knob ( clockwise or coun- terclockwise as needed and adjust the gain, the F (center frequency) and the Q.
MID GAIN : –6 to 6 (The factory default set- ting is “0”)
MID F : 700Hz/1KHz/2KHz (The factory default setting is “1k”)
of operation changes in the following order: |
Radio mode ➜ DAB mode ➜ CD mode ➜ DVD |
DECK mode ➜ CD changer mode ➜ MD |
changer mode ➜ TV mode ➜ AUX mode ➜ |
Radio mode... |
∗ External equipment not connected with CeNET |
is not displayed. |
mation on how to enter a title, refer to the sub- |
section “Entering titles” in section “Other |
Handy Functions”. |
Adjusting the non fader output volume
You can adjust the volume output from the unit’s non fader output terminal.
1.Press A-M button $ and select “NON-FAD VOL”.
2.Turning the Rotary knob ( clockwise in- creases the output volume; turning it coun- terclockwise decreases the output volume.
∗The factory default setting is “0”. (Setting range: –6 to 6)
MID Q : 1.5/2 (The factory default setting is “2”)
4.When the adfustment is complete, press A-M $ button several times until the function mode is reached.
Adjusting the TREBLE
The treble gain and treble F (center frequency) can be adjusted as follows.
1.Press the A-M button $ and select “TREB GAIN”.
