How to Operate the Machine

ENGLISH EN

Preparing The Machine For Use

BEFORE using any type of powered equipment, proper safety dictates you should visually inspect it.

1.Adjusting the Handle -

(a)Adjust the handle to a comfortable height by pulling outward on the two spring-loaded pins on each side of the handle.

(b)While holding the pins out, adjust the handle to the height desired.

(c)Release the pins so that they insert themselves into the locked positions. NOTE: It may be easier to stand to one side of the handle and reach across to the other side to make the adjustment.

2.Bonnet Filter- Make sure the bonnet air filter atop the engine is clean. It should be changed hourly and thoroughly cleaned before reuse.

3.Oil Level -

(a)Check the engine OIL LEVEL.

(b)With the buffer sitting in a level position, unscrew the yellow oil filler cap, pull out, and wipe dipstick off with a clean cloth.

(c)Insert the dipstick into the tube, but DO NOT screw it back in.

(d)Pull the dipstick out and check the oil level making sure the oil level is in the operating range (grid area) shown on the dipstick. If the oil level is in the "ADD" range, add enough engine oil to bring the oil level to the operating range. NOTE: NEVER overfill the engine oil as this can lead to irreparable damage to the engine.

4.Filling the Tank- Fill the tank following the instructions as given under the previous heading: "Refilling And Storing Propane Tanks." In addition, if your buffer came with an "80% Safety Fill Tank" then it should ONLY be filled through the threaded valve with the larger diameter that is covered by a yellow cap to ensure a "Full" level that is safe.

5.Pad and Pad Holder -

Inspect the condition of the pad and pad holder.

(a)Adjust handle to it's extreme upright position. (NOTE: Pins should be in the hole marked "TILTBACK").

(b)Grabbing the handle with both hands and placing your foot on the back deck of the burnisher for stability, pull back on the handle and tilt the machine back.

(c)Let the handle rest on the floor to hold the machine in the upright position.

(d)Go to the pad side of the machine for inspection and/or replacement. Is there a pad? Is it properly attached? What is it's condition? Ensure the pad is clean and has at least a thickness of 1/3 of an inch. Always turn off the engine before checking the pad.

6.Tank and Fuel Lines - The tank has already been covered but do the fuel lines show any sign of wear and tear, such as cracks or any corrosion? Screw the brass fuel line fitting onto the tank service valve, hand tight only. This connection MUST be secure because the service valve has a safety valve inside it which will only open if the brass fuel line fitting is COMPLETELY seated into the service valve.

7.Dust Containment Area -

Check the dust containment area and make sure that it is clean. This is the area underneath the propane tank.

(a)Remove the propane tank and then lift the black lid and locate the automotive-type filter.

(b)Inspect the filter. Is it dirty? Does it need to be cleaned or replaced? Make sure that the trough - that is outside of and below the level of the filter - is clean.

8.Dust Skirt - Check out the condition of the skirt that surrounds the deck. Is it in good condition? What is the condition of the rubber boot that connects the skirt to the rear part of the deck? Replace the boot if it is ripped or torn.

Starting the Engine

1.Open the service valve on the propane tank by turning counterclockwise, about one and a half turns.

2.Ensure the buffer is tilted back so that the pad is off the floor

on all machines without a clutch.

3.The Kawasaki 17 hp twin cylinder is designed to be started with the throttle in the idle position. This creates a vacuum necessary to open the lock-off valve inside the regulator. Actuation of the throttle lever will keep the lock-off valve from opening and the engine from getting fuel so the engine will not start. Proper mainte- nance will insure easy starting.

4.Engage starter for a MAXIMUM of 5 to 6 seconds or until the engine fires. Serious starter damage will result if this is exceeded and the warranty may not apply.

5.Operate the engine at half throttle for approximately two minutes for proper warm-up. Then advance to full throttle for best results.

NOTE: If the engine refuses to start, see the Trouble Shooting Guide.

Stopping The Engine

1.Close the service valve on the propane tank, by turning clockwise. This consumes all of the propane that is still in the fuel system.

2.ALWAYS allow the engine to run until it stops from lack of fuel, and then shut off the key switch. ** ONLY IN AN EMERGENCY should the "kill switch" on buffer be used.

3.Disconnect the fuel line from the tank.

4.REMEMBER, when you are finished with the machine, store the propane tank outside the building, in a safe place away from heat or direct sunlight.

Page -14-

Clarke® Operator's Manual (EN) - DC Propane Burnisher

Propane Floor Burnisher specifications

The Clarke Propane Floor Burnisher is an industry-leading machine designed for cleaning and maintaining various types of flooring surfaces, making it an essential tool for commercial cleaning operations. Renowned for its exceptional performance, reliability, and ease of use, this floor burnisher has become a preferred choice among facility managers and cleaning professionals.

One of the standout features of the Clarke Propane Floor Burnisher is its powerful propane engine, which ensures a consistent and efficient burnishing process. This engine provides the necessary torque to maintain high speeds, enabling users to achieve a pristine finish on a variety of hard floor surfaces, including vinyl, hardwood, and concrete. The burnisher is engineered with a low-emission, environmentally-friendly propane system, reducing its carbon footprint while delivering outstanding results.

Another key characteristic of the Clarke Propane Burnisher is its innovative design for user comfort and control. The machine is equipped with an ergonomic handle that can be adjusted to suit different operator heights, minimizing fatigue during extended use. The intuitive control panel allows for easy operation, including speed adjustments and ignition, ensuring that even novice operators can achieve professional-quality results.

The burnisher features a heavy-duty construction, designed to withstand the rigors of daily use in demanding environments. Its robust chassis provides stability and durability, while the large, high-quality pad assist in achieving a mirror-like shine. The burnisher also boasts a generous pad driver, allowing for compatibility with various pad types, giving users the flexibility to choose the best pad for their specific floor type and condition.

In terms of safety, the Clarke Propane Burnisher includes essential features such as an automatic shut-off mechanism that activates when the machine is in an upright position, preventing accidental operation. Additionally, the burnisher's design enhances visibility, helping operators navigate tight spaces with confidence.

Overall, the Clarke Propane Floor Burnisher is a versatile and powerful cleaning solution, combining advanced technology with practical features that enhance performance and user experience. Its unparalleled efficiency and ability to deliver impressive results make it an indispensable asset in any commercial cleaning arsenal. Whether for large facilities or smaller environments, this burnisher offers the dependability and results that cleaning professionals demand.

Clarke Propane Floor Burnisher How to Operate the Machine, Adjusting the Handle, Oil Level

Models: Propane Floor Burnisher

ENGLISH EN