Manuals / Compex Systems / Computer Equipment / Network Router

Compex Systems 802.11N manual Installation Direction

Models: 802.11N

1 77

Download 77 pages 29.76 Kb

Page 17

Installation Direction

Installation Direction

The directional antenna radiates the signal towards the front of the unit. The unit should be installed in a position whereby the front of the unit faces the direction you wish to send the signal to. Therefore the direction you wish to send the signal to has to be considered before going on to the next step of starting to set up the access point.

Image 17

Compex Systems 802.11N manual Installation Direction

Contents

Page Disclaimer Trademark InformationRF Exposure warning FCC NOTICEElectromagnetic Interference Conduction and Radiation EN 55022 CISPR Declaration of ConformityAccess the Web Interface Install the HardwareAdvance Wireless Tab IntroductionAppendix III- Advanced Settings Appendix II - Wireless with Router ModeAppendix IV- Services System TabIntroduction Overview the ProductHighly Secured Wireless Network Features and BenefitsuConfig Utility Point-to-Point & Point-to-MultiPoint SupportOperation Modes and Connection Examples Access Point and Access Point WDS ModeAccess Point WDS Mode Station Mode Point-to-MultiPoint Station WDS ModePoint-to-Point Static IP Address Router ModeDynamic IP Address PPP over Ethernet PPPoERepeater WDS Mode Features Device Panel Views and DescriptionsStatus and Indications higher lowInstallation Direction Install the HardwareSetting Up Antenna AlignmentAntenna Alignment Installation Direction CAT5/5e Networking Cable Setup RequirementsMount the Unit on a Pole Prepare Unit to mount to a pole PoE power input Passive PoE range 12V - 24V DC Select the Specify an IP address radio button Configure the IP AddressFor Windows 95/98/98SE/ME/NT Select the Ethernet adapter from the drop-down list and click OK Select the Use the following IP address radio button For Windows XP/2000Highlight Internet Protocol TCP/IP and click on the Properties button Click on the OK button to close all windows Access with uConfig Access the Web InterfaceSelect the access point from the products list and click on the Open Web button. To retrieve and display the latest devices in the list, click on the Refresh button Step User Name admin Password passwordStep It then opens the device home page. The Status pageAccess with a Web Browser It then opens the device home page. The Status page User Name admin Password passwordStep Main Menu Bar How to save changesNavigation Basic Network Tab LAN SetupNetwork Modes Bridging and Routing Network ModePrimary DNS IP optional Enable DNS ProxySecondary DNS IP optional DHCP ModeBasic Wireless Settings Basic Wireless TabEnable the radio Access Point Wireless ModeAccess Point WDS StationWireless Profile Access Point Parameters SettingsLocal AP-ESSID Country CodeChannel - Frequency Channel Spectrum WidthData Rate Rate AggressivenessRemote AP-ESSID Station Parameters SettingsRemote AP - Preferred MAC Wireless Mode StationFig 2.5 Channel Scan List In US Country Code Wireless Adapter modeChannel Scan List WPA or WPA2 Authentication Wireless SecurityWPA PSK Cipher TypeWPA + EAP Authentication PortPrimary Radius Server IP Secondary Radius Server IPWPA + EAPTLS, WPA-TTLS, WPA-PEAP User PasswordStation, Station WDS, Repeater WDS mode Identity User NameIEEE802.1x Key Rotation IEEE802.1x SettingsIEEE802.1x Key Length Authentication PortKey Type Authentication TypeCurrent Key WEP KeyVirtual Access Point VAP Long Range Parameters Setup Advance Wireless TabRTS Threshold Default is OFF Fragmentation Threshold Default is OFF Long Range ParametersNoise Immunity Signal Strength Indicator RSSIClick Advanced Network tab from menu to open the page below Advanced Network TabNAT Setup Spanning Tree SetupSpanning Tree Protocol Default is disabled. Check on box to enable NAT Enabled when in Router mode. Disabled when in Bridge modeAdding an entry from Custom Server Router Info Protocol version select RIPv1 or RIPv2 Bandwidth ControlRule Type select By IP or By MAC Firewall Setup Outbound Filtering Setup For security reason this service should not be open UPNP Default is disabled. Check on box to enabledClick Services tab from menu to open the page below Services TabEnable Ping Watchdog Default is disabled. Check on box to enable Auto-RebootPing Watchdog NTP Setup SNMP SetupEngine ID Default is Web HTTP SecuritySystem Log Setup Telnet Access SetupSSH Access Setup System Tab Firmware UpgradeEnable Read-Only Account Administrative and Read-only AccountHost Name Default administrator login credentials User Name adminDevice Maintenance Configuration ManagementMain Status PageStatus Reporting Radio LAN SettingWAN Setting WLAN Connected Status Station Connection Status InfoChannel Width WLAN Local AP StatisticsPage Appendix I - Network Bridge Mode Network SettingsBridge Mode Network Mode SelectionsDHCP Fallback IP Bridge IP AddressPrimary/Secondary DNS IP Spanning Tree Protocol Bridge mode Firewall Configuration SettingsAP-Router mode Network Settings Appendix II - Wireless with Router ModePage Port Forwarding Settings Bridge mode Firewall Configuration Settings Click Change button to save the changes made in the Network page Rate Aggressiveness Appendix III- Advanced SettingsAdvanced Wireless Setting Acknowledgement Timeout LED Thresholds Configuration Signal Strength LED SettingsSNMP Agent Appendix IV- ServicesPing WatchDog System Log NTP Client, Web, Telnet, SSH Server