Manuals / Compex Systems / Computer Equipment / Network Router

Compex Systems 802.11N manual Access the Web Interface, Access with uConfig

Models: 802.11N

1 77

Download 77 pages 29.76 Kb

Page 25

Access the Web Interface

Access the Web Interface

Access with uConfig

The UConfig utility provides direct access to the web interface.

Step 1:

Insert the Product CD into your CD-ROM drive, the CD will autorun.

Step 2:

From the Utilities section, select to install the uConfig utility to your hard disk.

Step 3:

After installation double-click on the uConfig icon and click on the Yes button.

Image 25

Compex Systems 802.11N manual Access the Web Interface, Access with uConfig

Contents

Page Disclaimer Trademark InformationRF Exposure warning FCC NOTICEElectromagnetic Interference Conduction and Radiation EN 55022 CISPR Declaration of ConformityAccess the Web Interface Install the HardwareAdvance Wireless Tab IntroductionAppendix III- Advanced Settings Appendix II - Wireless with Router ModeAppendix IV- Services System TabIntroduction Overview the ProductHighly Secured Wireless Network Features and BenefitsuConfig Utility Point-to-Point & Point-to-MultiPoint SupportAccess Point WDS Mode Access Point and Access Point WDS ModeOperation Modes and Connection Examples Station Mode Point-to-Point Station WDS ModePoint-to-MultiPoint Static IP Address Router ModeDynamic IP Address PPP over Ethernet PPPoERepeater WDS Mode Features Device Panel Views and DescriptionsStatus and Indications higher lowInstallation Direction Install the HardwareSetting Up Antenna AlignmentAntenna Alignment Installation Direction Mount the Unit on a Pole Setup RequirementsCAT5/5e Networking Cable Prepare Unit to mount to a pole PoE power input Passive PoE range 12V - 24V DC For Windows 95/98/98SE/ME/NT Configure the IP AddressSelect the Specify an IP address radio button Select the Ethernet adapter from the drop-down list and click OK Highlight Internet Protocol TCP/IP and click on the Properties button For Windows XP/2000Select the Use the following IP address radio button Click on the OK button to close all windows Access with uConfig Access the Web InterfaceSelect the access point from the products list and click on the Open Web button. To retrieve and display the latest devices in the list, click on the Refresh button Step User Name admin Password passwordStep It then opens the device home page. The Status pageAccess with a Web Browser Step User Name admin Password passwordIt then opens the device home page. The Status page Navigation How to save changesMain Menu Bar Basic Network Tab LAN SetupNetwork Modes Bridging and Routing Network ModePrimary DNS IP optional Enable DNS ProxySecondary DNS IP optional DHCP ModeEnable the radio Basic Wireless TabBasic Wireless Settings Access Point Wireless ModeAccess Point WDS StationWireless Profile Access Point Parameters SettingsLocal AP-ESSID Country CodeChannel - Frequency Channel Spectrum WidthData Rate Rate AggressivenessRemote AP-ESSID Station Parameters SettingsRemote AP - Preferred MAC Wireless Mode StationChannel Scan List Wireless Adapter modeFig 2.5 Channel Scan List In US Country Code WPA or WPA2 Authentication Wireless SecurityWPA PSK Cipher TypeWPA + EAP Authentication PortPrimary Radius Server IP Secondary Radius Server IPWPA + EAPTLS, WPA-TTLS, WPA-PEAP User PasswordStation, Station WDS, Repeater WDS mode Identity User NameIEEE802.1x Key Rotation IEEE802.1x SettingsIEEE802.1x Key Length Authentication PortKey Type Authentication TypeCurrent Key WEP KeyVirtual Access Point VAP Long Range Parameters Setup Advance Wireless TabRTS Threshold Default is OFF Fragmentation Threshold Default is OFF Long Range ParametersNoise Immunity Signal Strength Indicator RSSIClick Advanced Network tab from menu to open the page below Advanced Network TabNAT Setup Spanning Tree SetupSpanning Tree Protocol Default is disabled. Check on box to enable NAT Enabled when in Router mode. Disabled when in Bridge modeAdding an entry from Custom Server Rule Type select By IP or By MAC Bandwidth ControlRouter Info Protocol version select RIPv1 or RIPv2 Firewall Setup Outbound Filtering Setup For security reason this service should not be open UPNP Default is disabled. Check on box to enabledClick Services tab from menu to open the page below Services TabPing Watchdog Auto-RebootEnable Ping Watchdog Default is disabled. Check on box to enable NTP Setup SNMP SetupEngine ID Default is Web HTTP SecuritySSH Access Setup Telnet Access SetupSystem Log Setup System Tab Firmware UpgradeEnable Read-Only Account Administrative and Read-only AccountHost Name Default administrator login credentials User Name adminDevice Maintenance Configuration ManagementStatus Reporting Status PageMain WAN Setting LAN SettingRadio WLAN Connected Status Station Connection Status InfoChannel Width WLAN Local AP StatisticsPage Appendix I - Network Bridge Mode Network SettingsBridge Mode Network Mode SelectionsPrimary/Secondary DNS IP Bridge IP AddressDHCP Fallback IP Spanning Tree Protocol Bridge mode Firewall Configuration SettingsAP-Router mode Network Settings Appendix II - Wireless with Router ModePage Port Forwarding Settings Bridge mode Firewall Configuration Settings Click Change button to save the changes made in the Network page Advanced Wireless Setting Appendix III- Advanced SettingsRate Aggressiveness Acknowledgement Timeout LED Thresholds Configuration Signal Strength LED SettingsPing WatchDog Appendix IV- ServicesSNMP Agent System Log NTP Client, Web, Telnet, SSH Server