Manuals / Compex Systems / Computer Equipment / Network Router

Compex Systems 802.11N manual Virtual Access Point VAP

Models: 802.11N

1 77

Download 77 pages 29.76 Kb

Page 44

Virtual Access Point (VAP)

Virtual Access Point (VAP)

Virtual AP (VAP) implements mSSID (Multi-SSID) whereby a single wireless card can be setup with up to 3 virtual SSID of BSSID connections. Each VAP can be set with different security authentication mode.

Fig 2.11 Virtual AP (Only Available in Access Point/ Access Point WDS Mode)

All VAPs are created from the same radio they all share the same wireless channel, country code, channel spectrum width and transmit power.

Image 44

Compex Systems 802.11N manual Virtual Access Point VAP

Contents

Page Trademark Information DisclaimerFCC NOTICE RF Exposure warningDeclaration of Conformity Electromagnetic Interference Conduction and Radiation EN 55022 CISPRInstall the Hardware Access the Web InterfaceAdvance Wireless Tab IntroductionAppendix II - Wireless with Router Mode Appendix III- Advanced SettingsAppendix IV- Services System TabOverview the Product IntroductionFeatures and Benefits Highly Secured Wireless NetworkuConfig Utility Point-to-Point & Point-to-MultiPoint SupportOperation Modes and Connection Examples Access Point and Access Point WDS ModeAccess Point WDS Mode Station Mode Point-to-MultiPoint Station WDS ModePoint-to-Point Router Mode Static IP AddressDynamic IP Address PPP over Ethernet PPPoERepeater WDS Mode Device Panel Views and Descriptions FeaturesStatus and Indications higher lowInstall the Hardware Installation DirectionSetting Up Antenna AlignmentAntenna Alignment Installation Direction CAT5/5e Networking Cable Setup RequirementsMount the Unit on a Pole Prepare Unit to mount to a pole PoE power input Passive PoE range 12V - 24V DC Select the Specify an IP address radio button Configure the IP AddressFor Windows 95/98/98SE/ME/NT Select the Ethernet adapter from the drop-down list and click OK Select the Use the following IP address radio button For Windows XP/2000Highlight Internet Protocol TCP/IP and click on the Properties button Click on the OK button to close all windows Access the Web Interface Access with uConfigSelect the access point from the products list and click on the Open Web button. To retrieve and display the latest devices in the list, click on the Refresh button User Name admin Password password StepStep It then opens the device home page. The Status pageAccess with a Web Browser It then opens the device home page. The Status page User Name admin Password passwordStep Main Menu Bar How to save changesNavigation LAN Setup Basic Network TabNetwork Modes Bridging and Routing Network ModeEnable DNS Proxy Primary DNS IP optionalSecondary DNS IP optional DHCP ModeBasic Wireless Settings Basic Wireless TabEnable the radio Wireless Mode Access PointAccess Point WDS StationAccess Point Parameters Settings Wireless ProfileLocal AP-ESSID Country CodeChannel Spectrum Width Channel - FrequencyData Rate Rate AggressivenessStation Parameters Settings Remote AP-ESSIDRemote AP - Preferred MAC Wireless Mode StationFig 2.5 Channel Scan List In US Country Code Wireless Adapter modeChannel Scan List Wireless Security WPA or WPA2 AuthenticationWPA PSK Cipher TypeAuthentication Port WPA + EAPPrimary Radius Server IP Secondary Radius Server IPUser Password WPA + EAPTLS, WPA-TTLS, WPA-PEAPStation, Station WDS, Repeater WDS mode Identity User NameIEEE802.1x Settings IEEE802.1x Key RotationIEEE802.1x Key Length Authentication PortAuthentication Type Key TypeCurrent Key WEP KeyVirtual Access Point VAP Advance Wireless Tab Long Range Parameters SetupRTS Threshold Default is OFF Fragmentation Threshold Default is OFF Long Range ParametersSignal Strength Indicator RSSI Noise ImmunityAdvanced Network Tab Click Advanced Network tab from menu to open the page belowSpanning Tree Setup NAT SetupSpanning Tree Protocol Default is disabled. Check on box to enable NAT Enabled when in Router mode. Disabled when in Bridge modeAdding an entry from Custom Server Router Info Protocol version select RIPv1 or RIPv2 Bandwidth ControlRule Type select By IP or By MAC Firewall Setup Outbound Filtering Setup UPNP Default is disabled. Check on box to enabled For security reason this service should not be openServices Tab Click Services tab from menu to open the page belowEnable Ping Watchdog Default is disabled. Check on box to enable Auto-RebootPing Watchdog SNMP Setup NTP SetupEngine ID Default is Web HTTP SecuritySystem Log Setup Telnet Access SetupSSH Access Setup Firmware Upgrade System TabAdministrative and Read-only Account Enable Read-Only AccountHost Name Default administrator login credentials User Name adminConfiguration Management Device MaintenanceMain Status PageStatus Reporting Radio LAN SettingWAN Setting Station Connection Status Info WLAN Connected StatusChannel Width WLAN Local AP StatisticsPage Bridge Mode Network Settings Appendix I - NetworkBridge Mode Network Mode SelectionsDHCP Fallback IP Bridge IP AddressPrimary/Secondary DNS IP Bridge mode Firewall Configuration Settings Spanning Tree ProtocolAppendix II - Wireless with Router Mode AP-Router mode Network SettingsPage Port Forwarding Settings Bridge mode Firewall Configuration Settings Click Change button to save the changes made in the Network page Rate Aggressiveness Appendix III- Advanced SettingsAdvanced Wireless Setting Acknowledgement Timeout Signal Strength LED Settings LED Thresholds ConfigurationSNMP Agent Appendix IV- ServicesPing WatchDog NTP Client, Web, Telnet, SSH Server System Log