Manuals / Compex Systems / Computer Equipment / Network Router

Compex Systems 802.11N manual Ping Watchdog, Auto-Reboot

Models: 802.11N

1 77

Download 77 pages 29.76 Kb

Page 55

Ping Watchdog

Ping Watchdog

Enable Ping Watchdog: Default is disabled. Check on box to enable.

IP Address To Ping: Target IP address do ping test monitor.

Ping Interval: Default is 5 seconds (minimum). This is Ping test duration.

Startup Delay: Default is 60 seconds(minimum). One time delay after device startup.

Failed Count To Reboot: Default is 5. This is the number of ping failure count before device kick in the reboot process.

Auto-Reboot

Auto-Reboot Mode: Default is disabled. Select By Hour or By Time check.

This mode lets you preset a timer to automatically force a reboot. Timer can in fixed number of hours or at a specified time of day.

By Hour: Enter the number of hours device need to run before kick start reboot process.

By Time: Enter the specific time of day in hh:mm (24-hour format) to kick start reboots process.

Image 55

Compex Systems 802.11N manual Auto-Reboot, Enable Ping Watchdog Default is disabled. Check on box to enable

Contents

Page Disclaimer Trademark InformationRF Exposure warning FCC NOTICEElectromagnetic Interference Conduction and Radiation EN 55022 CISPR Declaration of ConformityIntroduction Install the HardwareAccess the Web Interface Advance Wireless TabSystem Tab Appendix II - Wireless with Router ModeAppendix III- Advanced Settings Appendix IV- ServicesIntroduction Overview the ProductPoint-to-Point & Point-to-MultiPoint Support Features and BenefitsHighly Secured Wireless Network uConfig UtilityAccess Point WDS Mode Access Point and Access Point WDS ModeOperation Modes and Connection Examples Station Mode Point-to-Point Station WDS ModePoint-to-MultiPoint PPP over Ethernet PPPoE Router ModeStatic IP Address Dynamic IP AddressRepeater WDS Mode higher low Device Panel Views and DescriptionsFeatures Status and IndicationsAntenna Alignment Install the HardwareInstallation Direction Setting UpAntenna Alignment Installation Direction Mount the Unit on a Pole Setup RequirementsCAT5/5e Networking Cable Prepare Unit to mount to a pole PoE power input Passive PoE range 12V - 24V DC For Windows 95/98/98SE/ME/NT Configure the IP AddressSelect the Specify an IP address radio button Select the Ethernet adapter from the drop-down list and click OK Highlight Internet Protocol TCP/IP and click on the Properties button For Windows XP/2000Select the Use the following IP address radio button Click on the OK button to close all windows Access with uConfig Access the Web InterfaceSelect the access point from the products list and click on the Open Web button. To retrieve and display the latest devices in the list, click on the Refresh button It then opens the device home page. The Status page User Name admin Password passwordStep StepAccess with a Web Browser Step User Name admin Password passwordIt then opens the device home page. The Status page Navigation How to save changesMain Menu Bar Network Mode LAN SetupBasic Network Tab Network Modes Bridging and RoutingDHCP Mode Enable DNS ProxyPrimary DNS IP optional Secondary DNS IP optionalEnable the radio Basic Wireless TabBasic Wireless Settings Station Wireless ModeAccess Point Access Point WDSCountry Code Access Point Parameters SettingsWireless Profile Local AP-ESSIDRate Aggressiveness Channel Spectrum WidthChannel - Frequency Data RateWireless Mode Station Station Parameters SettingsRemote AP-ESSID Remote AP - Preferred MACChannel Scan List Wireless Adapter modeFig 2.5 Channel Scan List In US Country Code Cipher Type Wireless SecurityWPA or WPA2 Authentication WPA PSKSecondary Radius Server IP Authentication PortWPA + EAP Primary Radius Server IPUser Name User PasswordWPA + EAPTLS, WPA-TTLS, WPA-PEAP Station, Station WDS, Repeater WDS mode IdentityAuthentication Port IEEE802.1x SettingsIEEE802.1x Key Rotation IEEE802.1x Key LengthWEP Key Authentication TypeKey Type Current KeyVirtual Access Point VAP Long Range Parameters Advance Wireless TabLong Range Parameters Setup RTS Threshold Default is OFF Fragmentation Threshold Default is OFFNoise Immunity Signal Strength Indicator RSSIClick Advanced Network tab from menu to open the page below Advanced Network TabNAT Enabled when in Router mode. Disabled when in Bridge mode Spanning Tree SetupNAT Setup Spanning Tree Protocol Default is disabled. Check on box to enableAdding an entry from Custom Server Rule Type select By IP or By MAC Bandwidth ControlRouter Info Protocol version select RIPv1 or RIPv2 Firewall Setup Outbound Filtering Setup For security reason this service should not be open UPNP Default is disabled. Check on box to enabledClick Services tab from menu to open the page below Services TabPing Watchdog Auto-RebootEnable Ping Watchdog Default is disabled. Check on box to enable Web HTTP Security SNMP SetupNTP Setup Engine ID Default isSSH Access Setup Telnet Access SetupSystem Log Setup System Tab Firmware UpgradeDefault administrator login credentials User Name admin Administrative and Read-only AccountEnable Read-Only Account Host NameDevice Maintenance Configuration ManagementStatus Reporting Status PageMain WAN Setting LAN SettingRadio WLAN Local AP Statistics Station Connection Status InfoWLAN Connected Status Channel WidthPage Network Mode Selections Bridge Mode Network SettingsAppendix I - Network Bridge ModePrimary/Secondary DNS IP Bridge IP AddressDHCP Fallback IP Spanning Tree Protocol Bridge mode Firewall Configuration SettingsAP-Router mode Network Settings Appendix II - Wireless with Router ModePage Port Forwarding Settings Bridge mode Firewall Configuration Settings Click Change button to save the changes made in the Network page Advanced Wireless Setting Appendix III- Advanced SettingsRate Aggressiveness Acknowledgement Timeout LED Thresholds Configuration Signal Strength LED SettingsPing WatchDog Appendix IV- ServicesSNMP Agent System Log NTP Client, Web, Telnet, SSH Server