Manuals / Compex Systems / Computer Equipment / Network Router

Compex Systems 802.11N manual Wireless Security, WPA or WPA2 Authentication, Wpa Psk, Cipher Type

Models: 802.11N

1 77

Download 77 pages 29.76 Kb

Page 39

Wireless Security

Wireless Security

All the wireless security settings are set under this section.

The operation of the Keys is the same for ALL the Wireless modes.

WPA or WPA2 Authentication

Fig 2.7 WPA (Access Point/Access Point WDS/Repeater WDS)

WPA PSK

PSK (Default) – WPA or WPA2 with Pre-shared Key method.

Cipher Type

TKIP - Temporal Key Integrity Protocol which uses RC4 encryption algorithm. AES - Advanced Encryption Standard (AES) algorithm.

AUTO (Default) – Automatically select between both algorithms.

Preshared Key

This option is available when WPA or WPA2, with PSK selected.

The pre-shared key is an alpha-numeric password between 8 and 63 characters long.

Image 39

Compex Systems 802.11N manual Wireless Security, WPA or WPA2 Authentication, Wpa Psk, Cipher Type, Preshared Key

Contents

Page Disclaimer Trademark InformationRF Exposure warning FCC NOTICEElectromagnetic Interference Conduction and Radiation EN 55022 CISPR Declaration of ConformityIntroduction Install the HardwareAccess the Web Interface Advance Wireless TabSystem Tab Appendix II - Wireless with Router ModeAppendix III- Advanced Settings Appendix IV- ServicesIntroduction Overview the ProductPoint-to-Point & Point-to-MultiPoint Support Features and BenefitsHighly Secured Wireless Network uConfig UtilityAccess Point and Access Point WDS Mode Access Point WDS ModeOperation Modes and Connection Examples Station Mode Station WDS Mode Point-to-PointPoint-to-MultiPoint PPP over Ethernet PPPoE Router ModeStatic IP Address Dynamic IP AddressRepeater WDS Mode higher low Device Panel Views and DescriptionsFeatures Status and IndicationsAntenna Alignment Install the HardwareInstallation Direction Setting UpAntenna Alignment Installation Direction Setup Requirements Mount the Unit on a PoleCAT5/5e Networking Cable Prepare Unit to mount to a pole PoE power input Passive PoE range 12V - 24V DC Configure the IP Address For Windows 95/98/98SE/ME/NTSelect the Specify an IP address radio button Select the Ethernet adapter from the drop-down list and click OK For Windows XP/2000 Highlight Internet Protocol TCP/IP and click on the Properties buttonSelect the Use the following IP address radio button Click on the OK button to close all windows Access with uConfig Access the Web InterfaceSelect the access point from the products list and click on the Open Web button. To retrieve and display the latest devices in the list, click on the Refresh button It then opens the device home page. The Status page User Name admin Password passwordStep StepAccess with a Web Browser User Name admin Password password StepIt then opens the device home page. The Status page How to save changes NavigationMain Menu Bar Network Mode LAN SetupBasic Network Tab Network Modes Bridging and RoutingDHCP Mode Enable DNS ProxyPrimary DNS IP optional Secondary DNS IP optionalBasic Wireless Tab Enable the radioBasic Wireless Settings Station Wireless ModeAccess Point Access Point WDSCountry Code Access Point Parameters SettingsWireless Profile Local AP-ESSIDRate Aggressiveness Channel Spectrum WidthChannel - Frequency Data RateWireless Mode Station Station Parameters SettingsRemote AP-ESSID Remote AP - Preferred MACWireless Adapter mode Channel Scan ListFig 2.5 Channel Scan List In US Country Code Cipher Type Wireless SecurityWPA or WPA2 Authentication WPA PSKSecondary Radius Server IP Authentication PortWPA + EAP Primary Radius Server IPUser Name User PasswordWPA + EAPTLS, WPA-TTLS, WPA-PEAP Station, Station WDS, Repeater WDS mode IdentityAuthentication Port IEEE802.1x SettingsIEEE802.1x Key Rotation IEEE802.1x Key LengthWEP Key Authentication TypeKey Type Current KeyVirtual Access Point VAP Long Range Parameters Advance Wireless TabLong Range Parameters Setup RTS Threshold Default is OFF Fragmentation Threshold Default is OFFNoise Immunity Signal Strength Indicator RSSIClick Advanced Network tab from menu to open the page below Advanced Network TabNAT Enabled when in Router mode. Disabled when in Bridge mode Spanning Tree SetupNAT Setup Spanning Tree Protocol Default is disabled. Check on box to enableAdding an entry from Custom Server Bandwidth Control Rule Type select By IP or By MACRouter Info Protocol version select RIPv1 or RIPv2 Firewall Setup Outbound Filtering Setup For security reason this service should not be open UPNP Default is disabled. Check on box to enabledClick Services tab from menu to open the page below Services TabAuto-Reboot Ping WatchdogEnable Ping Watchdog Default is disabled. Check on box to enable Web HTTP Security SNMP SetupNTP Setup Engine ID Default isTelnet Access Setup SSH Access SetupSystem Log Setup System Tab Firmware UpgradeDefault administrator login credentials User Name admin Administrative and Read-only AccountEnable Read-Only Account Host NameDevice Maintenance Configuration ManagementStatus Page Status ReportingMain LAN Setting WAN SettingRadio WLAN Local AP Statistics Station Connection Status InfoWLAN Connected Status Channel WidthPage Network Mode Selections Bridge Mode Network SettingsAppendix I - Network Bridge ModeBridge IP Address Primary/Secondary DNS IPDHCP Fallback IP Spanning Tree Protocol Bridge mode Firewall Configuration SettingsAP-Router mode Network Settings Appendix II - Wireless with Router ModePage Port Forwarding Settings Bridge mode Firewall Configuration Settings Click Change button to save the changes made in the Network page Appendix III- Advanced Settings Advanced Wireless SettingRate Aggressiveness Acknowledgement Timeout LED Thresholds Configuration Signal Strength LED SettingsAppendix IV- Services Ping WatchDogSNMP Agent System Log NTP Client, Web, Telnet, SSH Server