Manuals / Compex Systems / Computer Equipment / Network Router

Compex Systems 802.11N manual System Tab, Status Page, Appendix I - Network, Appendix IV- Services

Models: 802.11N

1 77

Download 77 pages 29.76 Kb

Page 6

System Tab	58
Firmware Upgrade	58
Host Name	59
Administrative and Read-only Account	59
Configuration Management	60
Device Maintenance	60
Status Page	61
Station Connection Status Info	63
Appendix I - Network	65
Appendix II – Wireless with Router Mode	68
Appendix III- Advanced Settings	73
Appendix IV- Services	76

Image 6

Compex Systems 802.11N System Tab, Status Page, Appendix I - Network, Appendix II - Wireless with Router Mode, Host Name

Contents

Page Trademark Information DisclaimerFCC NOTICE RF Exposure warningDeclaration of Conformity Electromagnetic Interference Conduction and Radiation EN 55022 CISPRAdvance Wireless Tab Install the HardwareAccess the Web Interface IntroductionAppendix IV- Services Appendix II - Wireless with Router ModeAppendix III- Advanced Settings System TabOverview the Product IntroductionuConfig Utility Features and BenefitsHighly Secured Wireless Network Point-to-Point & Point-to-MultiPoint SupportAccess Point and Access Point WDS Mode Access Point WDS ModeOperation Modes and Connection Examples Station Mode Station WDS Mode Point-to-PointPoint-to-MultiPoint Dynamic IP Address Router ModeStatic IP Address PPP over Ethernet PPPoERepeater WDS Mode Status and Indications Device Panel Views and DescriptionsFeatures higher lowSetting Up Install the HardwareInstallation Direction Antenna AlignmentAntenna Alignment Installation Direction Setup Requirements Mount the Unit on a PoleCAT5/5e Networking Cable Prepare Unit to mount to a pole PoE power input Passive PoE range 12V - 24V DC Configure the IP Address For Windows 95/98/98SE/ME/NTSelect the Specify an IP address radio button Select the Ethernet adapter from the drop-down list and click OK For Windows XP/2000 Highlight Internet Protocol TCP/IP and click on the Properties buttonSelect the Use the following IP address radio button Click on the OK button to close all windows Access the Web Interface Access with uConfigSelect the access point from the products list and click on the Open Web button. To retrieve and display the latest devices in the list, click on the Refresh button Step User Name admin Password passwordStep It then opens the device home page. The Status pageAccess with a Web Browser User Name admin Password password StepIt then opens the device home page. The Status page How to save changes NavigationMain Menu Bar Network Modes Bridging and Routing LAN SetupBasic Network Tab Network ModeSecondary DNS IP optional Enable DNS ProxyPrimary DNS IP optional DHCP ModeBasic Wireless Tab Enable the radioBasic Wireless Settings Access Point WDS Wireless ModeAccess Point StationLocal AP-ESSID Access Point Parameters SettingsWireless Profile Country CodeData Rate Channel Spectrum WidthChannel - Frequency Rate AggressivenessRemote AP - Preferred MAC Station Parameters SettingsRemote AP-ESSID Wireless Mode StationWireless Adapter mode Channel Scan ListFig 2.5 Channel Scan List In US Country Code WPA PSK Wireless SecurityWPA or WPA2 Authentication Cipher TypePrimary Radius Server IP Authentication PortWPA + EAP Secondary Radius Server IPStation, Station WDS, Repeater WDS mode Identity User PasswordWPA + EAPTLS, WPA-TTLS, WPA-PEAP User NameIEEE802.1x Key Length IEEE802.1x SettingsIEEE802.1x Key Rotation Authentication PortCurrent Key Authentication TypeKey Type WEP KeyVirtual Access Point VAP RTS Threshold Default is OFF Fragmentation Threshold Default is OFF Advance Wireless TabLong Range Parameters Setup Long Range ParametersSignal Strength Indicator RSSI Noise ImmunityAdvanced Network Tab Click Advanced Network tab from menu to open the page belowSpanning Tree Protocol Default is disabled. Check on box to enable Spanning Tree SetupNAT Setup NAT Enabled when in Router mode. Disabled when in Bridge modeAdding an entry from Custom Server Bandwidth Control Rule Type select By IP or By MACRouter Info Protocol version select RIPv1 or RIPv2 Firewall Setup Outbound Filtering Setup UPNP Default is disabled. Check on box to enabled For security reason this service should not be openServices Tab Click Services tab from menu to open the page belowAuto-Reboot Ping WatchdogEnable Ping Watchdog Default is disabled. Check on box to enable Engine ID Default is SNMP SetupNTP Setup Web HTTP SecurityTelnet Access Setup SSH Access SetupSystem Log Setup Firmware Upgrade System TabHost Name Administrative and Read-only AccountEnable Read-Only Account Default administrator login credentials User Name adminConfiguration Management Device MaintenanceStatus Page Status ReportingMain LAN Setting WAN SettingRadio Channel Width Station Connection Status InfoWLAN Connected Status WLAN Local AP StatisticsPage Bridge Mode Bridge Mode Network SettingsAppendix I - Network Network Mode SelectionsBridge IP Address Primary/Secondary DNS IPDHCP Fallback IP Bridge mode Firewall Configuration Settings Spanning Tree ProtocolAppendix II - Wireless with Router Mode AP-Router mode Network SettingsPage Port Forwarding Settings Bridge mode Firewall Configuration Settings Click Change button to save the changes made in the Network page Appendix III- Advanced Settings Advanced Wireless SettingRate Aggressiveness Acknowledgement Timeout Signal Strength LED Settings LED Thresholds ConfigurationAppendix IV- Services Ping WatchDogSNMP Agent NTP Client, Web, Telnet, SSH Server System Log