Manuals / Compex Systems / Computer Equipment / Network Router

Compex Systems 802.11N manual Configuration Management, Device Maintenance

Models: 802.11N

1 77

Download 77 pages 29.76 Kb

Page 60

Configuration Management

Configuration Management

Backup Configuration: click Download button to export the current configuration to a file.

Upload Configuration: click Browse button to navigate to and select the new configuration file or specify the full path to the configuration file location.

Activating the Upload button will transfer new configuration file to the system.

New configuration will be effective after the Apply button is activated and system reboot cycle is completed. Previous system configuration is deleted after Apply button is activated. It is highly recommended to backup the system configuration before uploading the new configuration.

Use only configuration backups of the same type device - configuration backed up from PowerStation2 suits only PowerStation2, but not LiteStation2 or LiteStation5! Behavior may be unpredictable when mixing configurations from different type devices.

Device Maintenance

The controls in this section are dedicated for the device maintenance routines: rebooting, resetting, generating of the support information report.

Reboot: activate Reboot control in order to initiate full reboot cycle of the device. Reboot effect is the same as the hardware reboot which is similar to the power off - power on cycle. The system configuration is not modified after the reboot cycle completes. Any non-applied changes will be lost.

Reset to Defaults: activate Reset to Defaults control in order to initiate reset the device to factory defaults routine. Reset routine initiates system Reboot process (similar to the power off - power on cycle). The running system configuration will be deleted and the default system configuration (all the system settings with no exception) will be set.

After the Reset to Defaults routine is completed, the device system will return to the default IP configuration (192.168.168.1/255.255.255.0) and will start operating in Station-Bridge mode. It is highly recommended to backup the system configuration before the Reset to Defaults is initiated.

Image 60

Compex Systems 802.11N manual Configuration Management, Device Maintenance

Contents

Page Trademark Information DisclaimerFCC NOTICE RF Exposure warningDeclaration of Conformity Electromagnetic Interference Conduction and Radiation EN 55022 CISPRInstall the Hardware Access the Web InterfaceAdvance Wireless Tab IntroductionAppendix II - Wireless with Router Mode Appendix III- Advanced SettingsAppendix IV- Services System TabOverview the Product IntroductionFeatures and Benefits Highly Secured Wireless NetworkuConfig Utility Point-to-Point & Point-to-MultiPoint SupportAccess Point and Access Point WDS Mode Access Point WDS ModeOperation Modes and Connection Examples Station Mode Station WDS Mode Point-to-PointPoint-to-MultiPoint Router Mode Static IP AddressDynamic IP Address PPP over Ethernet PPPoERepeater WDS Mode Device Panel Views and Descriptions FeaturesStatus and Indications higher lowInstall the Hardware Installation DirectionSetting Up Antenna AlignmentAntenna Alignment Installation Direction Setup Requirements Mount the Unit on a PoleCAT5/5e Networking Cable Prepare Unit to mount to a pole PoE power input Passive PoE range 12V - 24V DC Configure the IP Address For Windows 95/98/98SE/ME/NTSelect the Specify an IP address radio button Select the Ethernet adapter from the drop-down list and click OK For Windows XP/2000 Highlight Internet Protocol TCP/IP and click on the Properties buttonSelect the Use the following IP address radio button Click on the OK button to close all windows Access the Web Interface Access with uConfigSelect the access point from the products list and click on the Open Web button. To retrieve and display the latest devices in the list, click on the Refresh button User Name admin Password password StepStep It then opens the device home page. The Status pageAccess with a Web Browser User Name admin Password password StepIt then opens the device home page. The Status page How to save changes NavigationMain Menu Bar LAN Setup Basic Network TabNetwork Modes Bridging and Routing Network ModeEnable DNS Proxy Primary DNS IP optionalSecondary DNS IP optional DHCP ModeBasic Wireless Tab Enable the radioBasic Wireless Settings Wireless Mode Access PointAccess Point WDS StationAccess Point Parameters Settings Wireless ProfileLocal AP-ESSID Country CodeChannel Spectrum Width Channel - FrequencyData Rate Rate AggressivenessStation Parameters Settings Remote AP-ESSIDRemote AP - Preferred MAC Wireless Mode StationWireless Adapter mode Channel Scan ListFig 2.5 Channel Scan List In US Country Code Wireless Security WPA or WPA2 AuthenticationWPA PSK Cipher TypeAuthentication Port WPA + EAPPrimary Radius Server IP Secondary Radius Server IPUser Password WPA + EAPTLS, WPA-TTLS, WPA-PEAPStation, Station WDS, Repeater WDS mode Identity User NameIEEE802.1x Settings IEEE802.1x Key RotationIEEE802.1x Key Length Authentication PortAuthentication Type Key TypeCurrent Key WEP KeyVirtual Access Point VAP Advance Wireless Tab Long Range Parameters SetupRTS Threshold Default is OFF Fragmentation Threshold Default is OFF Long Range ParametersSignal Strength Indicator RSSI Noise ImmunityAdvanced Network Tab Click Advanced Network tab from menu to open the page belowSpanning Tree Setup NAT SetupSpanning Tree Protocol Default is disabled. Check on box to enable NAT Enabled when in Router mode. Disabled when in Bridge modeAdding an entry from Custom Server Bandwidth Control Rule Type select By IP or By MACRouter Info Protocol version select RIPv1 or RIPv2 Firewall Setup Outbound Filtering Setup UPNP Default is disabled. Check on box to enabled For security reason this service should not be openServices Tab Click Services tab from menu to open the page belowAuto-Reboot Ping WatchdogEnable Ping Watchdog Default is disabled. Check on box to enable SNMP Setup NTP SetupEngine ID Default is Web HTTP SecurityTelnet Access Setup SSH Access SetupSystem Log Setup Firmware Upgrade System TabAdministrative and Read-only Account Enable Read-Only AccountHost Name Default administrator login credentials User Name adminConfiguration Management Device MaintenanceStatus Page Status ReportingMain LAN Setting WAN SettingRadio Station Connection Status Info WLAN Connected StatusChannel Width WLAN Local AP StatisticsPage Bridge Mode Network Settings Appendix I - NetworkBridge Mode Network Mode SelectionsBridge IP Address Primary/Secondary DNS IPDHCP Fallback IP Bridge mode Firewall Configuration Settings Spanning Tree ProtocolAppendix II - Wireless with Router Mode AP-Router mode Network SettingsPage Port Forwarding Settings Bridge mode Firewall Configuration Settings Click Change button to save the changes made in the Network page Appendix III- Advanced Settings Advanced Wireless SettingRate Aggressiveness Acknowledgement Timeout Signal Strength LED Settings LED Thresholds ConfigurationAppendix IV- Services Ping WatchDogSNMP Agent NTP Client, Web, Telnet, SSH Server System Log