Manuals / Compex Systems / Computer Equipment / Network Router

Compex Systems 802.11N manual Noise Immunity, Signal Strength Indicator RSSI

Models: 802.11N

1 77

Download 77 pages 29.76 Kb

Page 46

Noise Immunity:

Noise Immunity:

Check to enable. When enabled, it automatically adjusts the signal/noise level for best performance. In low noise environment it is recommended to turn off this function.

Signal Strength Indicator (RSSI):

The default values are LED1-Red (10), LED2-Yellow (20), LED3-Green (40) Each LEDs when turn on indicates the RSSI signal strength has hit over the value. e.g. When LED1 and LED2 light up it indicate the RSSI is greater than 20.

When all 4 LEDs light up it indicate RSSI is greater than 40.

For long distant installation when signal strength expected to be about 20-30, the values can be adjusted to display over this new range.

e.g. the LEDs values can be adjusted as follows: LED1 (RSSI value=7)

LED2 (RSSI value=15) LED3 (RSSI value=22) LED4 (RSSI value=27)

Image 46

Compex Systems 802.11N manual Noise Immunity, Signal Strength Indicator RSSI

Contents

Page Trademark Information DisclaimerFCC NOTICE RF Exposure warningDeclaration of Conformity Electromagnetic Interference Conduction and Radiation EN 55022 CISPRAdvance Wireless Tab Install the HardwareAccess the Web Interface IntroductionAppendix IV- Services Appendix II - Wireless with Router ModeAppendix III- Advanced Settings System TabOverview the Product IntroductionuConfig Utility Features and BenefitsHighly Secured Wireless Network Point-to-Point & Point-to-MultiPoint SupportAccess Point WDS Mode Access Point and Access Point WDS ModeOperation Modes and Connection Examples Station Mode Point-to-Point Station WDS ModePoint-to-MultiPoint Dynamic IP Address Router ModeStatic IP Address PPP over Ethernet PPPoERepeater WDS Mode Status and Indications Device Panel Views and DescriptionsFeatures higher lowSetting Up Install the HardwareInstallation Direction Antenna AlignmentAntenna Alignment Installation Direction Mount the Unit on a Pole Setup RequirementsCAT5/5e Networking Cable Prepare Unit to mount to a pole PoE power input Passive PoE range 12V - 24V DC For Windows 95/98/98SE/ME/NT Configure the IP AddressSelect the Specify an IP address radio button Select the Ethernet adapter from the drop-down list and click OK Highlight Internet Protocol TCP/IP and click on the Properties button For Windows XP/2000Select the Use the following IP address radio button Click on the OK button to close all windows Access the Web Interface Access with uConfigSelect the access point from the products list and click on the Open Web button. To retrieve and display the latest devices in the list, click on the Refresh button Step User Name admin Password passwordStep It then opens the device home page. The Status pageAccess with a Web Browser Step User Name admin Password passwordIt then opens the device home page. The Status page Navigation How to save changesMain Menu Bar Network Modes Bridging and Routing LAN SetupBasic Network Tab Network ModeSecondary DNS IP optional Enable DNS ProxyPrimary DNS IP optional DHCP ModeEnable the radio Basic Wireless TabBasic Wireless Settings Access Point WDS Wireless ModeAccess Point StationLocal AP-ESSID Access Point Parameters SettingsWireless Profile Country CodeData Rate Channel Spectrum WidthChannel - Frequency Rate AggressivenessRemote AP - Preferred MAC Station Parameters SettingsRemote AP-ESSID Wireless Mode StationChannel Scan List Wireless Adapter modeFig 2.5 Channel Scan List In US Country Code WPA PSK Wireless SecurityWPA or WPA2 Authentication Cipher TypePrimary Radius Server IP Authentication PortWPA + EAP Secondary Radius Server IPStation, Station WDS, Repeater WDS mode Identity User PasswordWPA + EAPTLS, WPA-TTLS, WPA-PEAP User NameIEEE802.1x Key Length IEEE802.1x SettingsIEEE802.1x Key Rotation Authentication PortCurrent Key Authentication TypeKey Type WEP KeyVirtual Access Point VAP RTS Threshold Default is OFF Fragmentation Threshold Default is OFF Advance Wireless TabLong Range Parameters Setup Long Range ParametersSignal Strength Indicator RSSI Noise ImmunityAdvanced Network Tab Click Advanced Network tab from menu to open the page belowSpanning Tree Protocol Default is disabled. Check on box to enable Spanning Tree SetupNAT Setup NAT Enabled when in Router mode. Disabled when in Bridge modeAdding an entry from Custom Server Rule Type select By IP or By MAC Bandwidth ControlRouter Info Protocol version select RIPv1 or RIPv2 Firewall Setup Outbound Filtering Setup UPNP Default is disabled. Check on box to enabled For security reason this service should not be openServices Tab Click Services tab from menu to open the page belowPing Watchdog Auto-RebootEnable Ping Watchdog Default is disabled. Check on box to enable Engine ID Default is SNMP SetupNTP Setup Web HTTP SecuritySSH Access Setup Telnet Access SetupSystem Log Setup Firmware Upgrade System TabHost Name Administrative and Read-only AccountEnable Read-Only Account Default administrator login credentials User Name adminConfiguration Management Device MaintenanceStatus Reporting Status PageMain WAN Setting LAN SettingRadio Channel Width Station Connection Status InfoWLAN Connected Status WLAN Local AP StatisticsPage Bridge Mode Bridge Mode Network SettingsAppendix I - Network Network Mode SelectionsPrimary/Secondary DNS IP Bridge IP AddressDHCP Fallback IP Bridge mode Firewall Configuration Settings Spanning Tree ProtocolAppendix II - Wireless with Router Mode AP-Router mode Network SettingsPage Port Forwarding Settings Bridge mode Firewall Configuration Settings Click Change button to save the changes made in the Network page Advanced Wireless Setting Appendix III- Advanced SettingsRate Aggressiveness Acknowledgement Timeout Signal Strength LED Settings LED Thresholds ConfigurationPing WatchDog Appendix IV- ServicesSNMP Agent NTP Client, Web, Telnet, SSH Server System Log