Manuals / Craftsman / Power Tools / Saw

Craftsman 315.273731 owner manual Bench TOOLS, Visit Your Nearest Sears Retail Store

Models: 315.273731

1 80

Download 80 pages 61.15 Kb

Page 11

Resin

A sticky, sap-based substance.

Rip Cut

In a radial saw, a cut made with the blade parallel to the fence and perpendicular to the arm. Can be across or with the grain. The teeth point up at the point of contact with the wood.

Sawblade Path

The area directly in line with the blade -- over, under, behind, or in front of it. Also, the workpiece area which will be or has been cut by the blade.

Set

The distance that the tip of the saw blade tooth is off set from the face of the blade.

Throw-Back

Saw throwing back a workpiece similar to kickback.

Through Sawing

Any cutting operation where the blade extends completely through the workpiece.

Trailing End

The workpiece end last cut by the blade in a rip cut.

Workpiece

The item on which the cutting operation is being done. The surfaces of a workpiece are commonly referred to as faces, ends, and edges.

Worktable

The surface on which the workpiece rests while performing a cutting operation.

,_ WARNING: To prevent accidental starting that could cause possible serious personal injury,

assemble all parts to your saw before connecting it to power supply. The saw should never be connected to the power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use.

_ WARNING: If any parts are missing, do not operate this tool until the missing parts are

replaced. Failure to do so could result in possible serious personal injury.

FOR A COM PLETE SELECTION OF ACCESSORIES FORTHIS AND OTHER CRAFTSMAN POWER AND

BENCH TOOLS, VISIT YOUR NEAREST SEARS RETAIL STORE.

•Carefully remove all parts from the carton and place the saw on a level work surface. Separate and check against the list of loose parts.

•Do not discard the packing materials until you have carefully inspected the saw, identified all parts, and satisfactorily operated your new saw.

Note: If any parts are damaged or missing, do not attempt to plug in the power cord and turn the switch on until the damaged or missing parts are obtained and are installed correctly.

11	CRRR'._MRN° RADIALSAW315.273731

Image 11

Craftsman 315.273731 owner manual Bench TOOLS, Visit Your Nearest Sears Retail Store

Contents

Radial ARM SAW Full TWO Year Warranty on Craftsman Tool Installing Yoke Assembly Removing Equipment Safety Alert SymbolAlways Wear Safety Glasses with Side 5CRRFI.HRNRADIAL SAW315.273731 Do not USE a Person AS a Substitute 7IRRIq.HRH Radial SAW315.273731 Grounding PIN Coverofgrounded Outletbox Extension Cords Bladearbor PAN Headscrew Motorcover Lift Motorcoverto ExposeswitchSee Figures Dado Cut Bench TOOLS, Visit Your Nearest Sears Retail Store Sawassemblyshownas Packed SawAssembly Switch HIJ Bcde Framingsquare HEX KeysPencil Motor Know Your Radial SAWSee a Yoke Locklever Motor See Figures 8A-8DMiterscale Armlockknob Yokepivotlatch RIP Scales Lockhandle FEN Elevating Handwheel Spacer ANTI-KICKBACK DustguideBladeguard Long See Figures 9A 9CHexnut Elevating Shaft Handwheel See FigureLEG Armlockknob Armcap See Figures 12A 12CArmviewedfrombelow Washersupport Bladeto Blade Arbor Mounttable Supports Usingthesehole LocationsTableflat Thumbscrew Blade Guard Blade Armcapmotor Yokelock Yoke AssemblyArmlockknob ARM Turncounterclock ARM To Tighten Lockwheel Locklever See Figures 17A -17CClampbolt Bevel Tube See Figures 19A 19D CAP Screws Rotation AdjustmentColumntube Columnsupport Graspand Hold Adjusting the Carriage BearingsSee Figures 20A and 20B Carriagebearing Rightside Armlock Knob Bevel Locklever BladewrenchAT Back Tablesupport Elevating Handwheel See Figures 22A 22C See Figures 24A 24C Installing Rear TABLE, Spacer TABLE, FENCE, and ClampsLeveling the Front Table Phillipsscrewdriver On PAN Headscrew Setscrew Loosen Thumbscrew Clamp Bracket Squarenut Clampshown AssembledRectangle Support Rivingknifeontop of Fence TOO Farleftof Blade See Figures 26A 26CKnob 3KPAWLS Spring Carriage Screws Installing RIP Scale IndicatorsRipscale Indicator Carriage Cover Speednut Linealongthis Edge Miterindicatorarm LockknobAligning the ARM for Cross Cuts Edge Armlockknob Bevel Indexcap Lock Lever Bladesquareto Table Noadjustmentneeded Framing Square GAPAligning Blade to Table AT 0 Bevel See Figures 29A 29D ARM Lockknob No Adjustmentneeded FramingSquaring Blade to Fence See Figures 30A 30C See Figures 31A-31C Noadjustment NeededAdjustment GAP Needed Paralleling Blade to Table Yokepivot Latch Aligning the RIP Scale IndicatorsSee Figures 32A 32B Socket Installing Control CUT DeviceBarrel Fitting RIP Cuts Basic Operation of the Radial ARM SAWTypes of Cuts Cross Cuts Causes of Kickback Switch and Switch KEYInsertswitchkey Switchon Switchoff Featherboards Cutting AidsPushsticks Pushblocks Tableclamps Making a Cross CUT Carriage Yokelock Lock Handle Bladeguard Bevel Indicator Ercut LockleverMaking a Miter CUT Armmiterscale Lockknob Yoke Pivot Latch Riving Knife Yokelock Handle Making a Bevel CUTBeveledcut ARM Lockknob Armpivot Latch Lock SwitchyokelockMaking a Compound Cross CUT Miterscale RiP CUT Hazards and Precautions Making a RIP CUT See Figure Review the Hazards and Precautions Supportlongworkpieces Making Other CutsSee Figures 47 Cutting Long Workpieces NON-THROUGH Cuts ControlCut Settings MOTOR/ELECTRICAL General Maintenance Problem See Adjusting Column Carriage Assembly in AssemDures in Adjustment Assembly section See Adjusting the Column Tube in Assembly section Problem Causesolution Remove and clean tables 57CIIFTSMRRADIALSAW315.273731 Figure a See Figures F and G Quan Parts List for Figure aKEY Part NO. Number Description See Figure C Craftsman Radial ARM SAW- Model no KEY Part NO. Number Parts List for Figure B Figure C KEY Part Number Parts List for Figure C 27--+---17 Parts List for Figure D Figure E KEY Part NO.NUMBER Parts List for Figure E See Figure G Figure F 69IRRFTSMRN RADIALSAW315.273731 Parts List for Figure F See Figure H See Figure F Number Parts List for Figure G Figure H Craftsman Radial ARM SAW- Model no Parts List for Figure H 1725 1824 Description Quan Parts List for FigureKEY Part Description Figure J Parts List for Figure J Figure K Parts List for Figure K Call Service and Repair Parts