Manuals / Craftsman / Power Tools / Saw

Craftsman 315.273731 owner manual See Figures 19A 19D, Tube

Models: 315.273731

1 80

Download 80 pages 61.15 Kb

Page 26

TIGHTENING THE ARM AND COLUMN

See Figure 18.

There should be no play, vertical or horizontal, in the arm relative to the column. If you can move the arm up, down or sideways when the arm lock knob is unlocked, use the following steps to tighten the arm.

Note: The arm should pivot only when the arm lock knob is unlocked and pulled forward to com- press the spring.

•Using a phillips screwdriver, remove the rear cover screws (2) and rear cover from the back of the arm. This uncovers the bolts on the column.

•Tighten the top two bolts evenly until the arm is firm and there is no vertical or horizontal movement.

•Also check the two bottom hex nuts. It is not necessary to tighten them as tight as the upper bolts. However they should be tightened even and snug.

•Replace the rear cover and rear cover screws.

•Tighten screws securely.

REAR

COVERSCREWS

REAR

COVER

HEXBOLT(2)

ADJUSTING THE COLUMN TUBE

See Figures 19A - 19D.

The purpose of this procedure is to check whether the inner column tube is snug in the housing and to remove any looseness. Looseness could result in a poor cut or difficulty in elevating the carriage. The column tube is the upper portion of the column and extends from the column support.

Note: It is critical to remove all looseness with this procedure. If this procedure is not done cor- rectly, following adjustments will be wrong and could result in machine damage.

This procedure checks both the elevating action and the rotating action. If a check does not show loose- ness, do not perform the adjustment.

•If the arm is not at 0°(straight forward), release the arm lock knob, set the arm, and re-lock the arm lock knob.

•Elevation check. To check the elevation movement, place your hand under the front of the radial arm. Press upward on the radial arm. There should be no play between the column tube and the column support. The whole assembly should move as one. See Figure 19A.

COLUMN ARM

TUBE

COLUMN

SUPPORT

Fig. 19A

HEXNUT(2)

Fig. 18

CR_FT_MRN °RADIAL SAW 315.273731

26

Image 26

Craftsman 315.273731 owner manual See Figures 19A 19D, Tube

Contents

Radial ARM SAW Full TWO Year Warranty on Craftsman Tool Installing Yoke Assembly Removing Equipment Safety Alert SymbolAlways Wear Safety Glasses with Side 5CRRFI.HRNRADIAL SAW315.273731 Do not USE a Person AS a Substitute 7IRRIq.HRH Radial SAW315.273731 Extension Cords Grounding PIN Coverofgrounded Outletbox Bladearbor PAN Headscrew Motorcover Lift Motorcoverto ExposeswitchSee Figures Dado Cut Bench TOOLS, Visit Your Nearest Sears Retail Store SawAssembly Sawassemblyshownas Packed Switch Bcde HIJ Framingsquare HEX KeysPencil Yoke Know Your Radial SAWSee a Motor Lockhandle See Figures 8A-8DMiterscale Armlockknob Yokepivotlatch RIP Scales Locklever Motor Spacer FEN Elevating Handwheel ANTI-KICKBACK DustguideBladeguard Long See Figures 9A 9CHexnut Elevating Shaft Handwheel See FigureLEG Armlockknob Armcap See Figures 12A 12CArmviewedfrombelow Thumbscrew Blade Guard Blade Blade Arbor Mounttable Supports Usingthesehole LocationsTableflat Washersupport Bladeto ARM To Tighten Lockwheel Yoke AssemblyArmlockknob ARM Turncounterclock Armcapmotor Yokelock Bevel See Figures 17A -17CClampbolt Locklever See Figures 19A 19D Tube CAP Screws Rotation AdjustmentColumntube Columnsupport Carriagebearing Adjusting the Carriage BearingsSee Figures 20A and 20B Graspand Hold Tablesupport Elevating Handwheel Armlock Knob Bevel Locklever BladewrenchAT Back Rightside See Figures 22A 22C Phillipsscrewdriver On PAN Headscrew Setscrew Installing Rear TABLE, Spacer TABLE, FENCE, and ClampsLeveling the Front Table See Figures 24A 24C Support Thumbscrew Clamp Bracket Squarenut Clampshown AssembledRectangle Loosen 3KPAWLS See Figures 26A 26CKnob Rivingknifeontop of Fence TOO Farleftof Blade Spring Carriage Screws Installing RIP Scale IndicatorsRipscale Indicator Carriage Cover Speednut Edge Miterindicatorarm LockknobAligning the ARM for Cross Cuts Linealongthis Edge See Figures 29A 29D Bladesquareto Table Noadjustmentneeded Framing Square GAPAligning Blade to Table AT 0 Bevel Armlockknob Bevel Indexcap Lock Lever See Figures 30A 30C No Adjustmentneeded FramingSquaring Blade to Fence ARM Lockknob Paralleling Blade to Table Noadjustment NeededAdjustment GAP Needed See Figures 31A-31C Yokepivot Latch Aligning the RIP Scale IndicatorsSee Figures 32A 32B Socket Installing Control CUT DeviceBarrel Fitting Cross Cuts Basic Operation of the Radial ARM SAWTypes of Cuts RIP Cuts Switchon Switchoff Switch and Switch KEYInsertswitchkey Causes of Kickback Pushblocks Cutting AidsPushsticks Featherboards Making a Cross CUT Tableclamps Armmiterscale Lockknob Yoke Pivot Latch Lock Handle Bladeguard Bevel Indicator Ercut LockleverMaking a Miter CUT Carriage Yokelock Riving Knife Yokelock Handle Making a Bevel CUTBeveledcut ARM Lockknob Miterscale SwitchyokelockMaking a Compound Cross CUT Armpivot Latch Lock RiP CUT Hazards and Precautions See Figure Review the Hazards and Precautions Making a RIP CUT Cutting Long Workpieces Making Other CutsSee Figures 47 Supportlongworkpieces ControlCut Settings NON-THROUGH Cuts General Maintenance MOTOR/ELECTRICAL Problem Assembly section Carriage Assembly in AssemDures in Adjustment See Adjusting Column Problem Causesolution See Adjusting the Column Tube in Assembly section Remove and clean tables 57CIIFTSMRRADIALSAW315.273731 Figure a See Figures F and G Description Parts List for Figure aKEY Part NO. Number Quan Craftsman Radial ARM SAW- Model no See Figure C Parts List for Figure B KEY Part NO. Number Figure C Parts List for Figure C KEY Part Number 27--+---17 Parts List for Figure D Figure E Parts List for Figure E KEY Part NO.NUMBER Figure F See Figure G Parts List for Figure F 69IRRFTSMRN RADIALSAW315.273731 See Figure F See Figure H Parts List for Figure G Number Figure H Parts List for Figure H Craftsman Radial ARM SAW- Model no 1725 1824 Description Quan Parts List for FigureKEY Part Description Figure J Parts List for Figure J Figure K Parts List for Figure K Service and Repair Parts Call