CY14B101L
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the device. These user guidelines are not tested.
Storage Temperature | |
Ambient Temperature with |
|
Power Applied | |
Supply Voltage on VCC Relative to GND | |
Voltage Applied to Outputs | |
in High Z State | |
Input Voltage | |
Transient Voltage (<20 ns) on |
|
Any Pin to Ground Potential |
Package Power Dissipation |
|
Capability (TA = 25°C) | 1.0W |
Surface Mount Lead Soldering |
|
Temperature (3 Seconds) | +260°C |
DC output Current (1 output at a time, 1s duration) .... 15 mA
Static Discharge Voltage | > 2001V |
| |
Latch Up Current | > 200 mA |
Operating Range
Range | Ambient Temperature | VCC |
Commercial | 0°C to +70°C | 2.7V to 3.6V |
|
|
|
Industrial | 2.7V to 3.6V | |
|
|
|
DC Electrical Characteristics
Over the operating range (VCC = 2.7V to 3.6V) [4, 5]
Parameter | Description |
|
|
|
| Test Conditions |
|
|
| Min | Max | Unit | ||||
ICC1 | Average VCC Current | tRC = 25 ns |
|
|
|
|
| Commercial |
| 65 | mA | |||||
|
|
| tRC = 35 ns |
|
|
|
|
|
|
|
|
| 55 | mA | ||
|
|
| tRC = 45 ns |
|
|
|
|
|
|
|
|
| 50 |
| ||
|
|
| Dependent on output loading and cycle rate. |
|
|
|
|
|
| |||||||
|
|
| Industrial |
| 70 | mA | ||||||||||
|
|
| Values obtained without output loads. |
| ||||||||||||
|
|
|
|
|
|
| 60 | mA | ||||||||
|
|
| IOUT = 0 mA. |
|
|
|
| |||||||||
|
|
|
|
|
|
| 55 | mA | ||||||||
|
|
|
|
|
|
|
|
|
| |||||||
ICC2 | Average VCC Current |
| All Inputs Do Not Care, VCC = Max |
|
|
|
| 6 | mA | |||||||
| during STORE |
| Average current for duration tSTORE |
|
|
|
|
|
| |||||||
ICC3 | Average VCC Current at |
|
|
| > (VCC | – 0.2V). All other inputs cycling. |
|
|
|
| 10 | mA | ||||
| WE |
|
|
|
| |||||||||||
| tRC= 200 ns, 5V, 25°C |
| Dependent on output loading and cycle rate. Values obtained |
|
|
| ||||||||||
| Typical |
| without output loads. |
|
|
|
|
|
| |||||||
ICC4 | Average VCAP Current |
| All Inputs Do Not Care, VCC = Max |
|
|
|
| 3 | mA | |||||||
| during AutoStore Cycle |
| Average current for duration tSTORE |
|
|
|
|
|
| |||||||
ISB | VCC Standby Current |
|
| > (VCC – 0.2V). All others VIN < 0.2V or > (VCC – 0.2V). |
| 3 | mA | |||||||||
| CE |
| ||||||||||||||
|
|
| Standby current level after nonvolatile cycle is complete. |
|
|
| ||||||||||
|
|
| Inputs are static. f = 0 MHz. |
|
|
|
|
|
| |||||||
IIX | Input Leakage Current | VCC = Max, VSS < VIN < VCC |
|
|
| +1 | μA | |||||||||
IOZ | Off State Output |
| VCC = Max, VSS < VIN < VCC, |
| or |
| > VIH or |
| < VIL | +1 | μA | |||||
| CE | OE | WE | |||||||||||||
| Leakage Current |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VIH | Input HIGH Voltage |
|
|
|
|
|
|
|
|
|
|
|
| 2.0 | VCC + | V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0.5 |
|
VIL | Input LOW Voltage |
|
|
|
|
|
|
|
|
|
|
|
| VSS – 0.5 | 0.8 | V |
VOH | Output HIGH Voltage |
| IOUT = |
|
|
| 2.4 |
| V | |||||||
VOL | Output LOW Voltage | IOUT = 4 mA |
|
|
|
| 0.4 | V | ||||||||
VCAP | Storage Capacitor | Between VCAP pin and Vss, 6V rated. |
|
|
| 17 | 120 | uF | ||||||||
Notes
4.The HSB pin has IOUT =
5.VIH changes by 100 mV when VCC > 3.5V.
Document Number: | Page 7 of 18 |
[+] Feedback
