Cypress CY7C1520KV18, CY7C1516KV18 Maximum Ratings, Operating Range, Electrical Characteristics

CY7C1516KV18, CY7C1527KV18 CY7C1518KV18, CY7C1520KV18

Maximum Ratings

Exceeding maximum ratings may impair the useful life of the device. These user guidelines are not tested.

Storage Temperature ................................. –65°C to +150°C

Ambient Temperature with Power Applied.. –55°C to +125°C

Supply Voltage on VDD Relative to GND		–0.5V to +2.9V
Supply Voltage on VDDQ Relative to GND		–0.5V to +VDD
DC Applied to Outputs in High-Z	–0.5V to VDDQ + 0.3V
DC Input Voltage [11]	–0.5V to V + 0.3V
		DD

Current into Outputs (LOW)			20 mA
Static Discharge Voltage (MIL-STD-883, M 3015)....			>2001V
Latch up Current	.....................................................		>200 mA
Operating Range
Range	Ambient	VDD [15]	VDDQ [15]
	Temperature (TA)
Commercial	0°C to +70°C	1.8 ± 0.1V	1.4V to
			VDD
Industrial	–40°C to +85°C

Electrical Characteristics

DC Electrical Characteristics

Over the Operating Range [12]

Parameter	Description	Test Conditions			Min	Typ	Max	Unit
VDD	Power Supply Voltage				1.7	1.8	1.9	V
VDDQ	IO Supply Voltage				1.4	1.5	VDD	V
VOH	Output HIGH Voltage	Note 16			VDDQ/2 – 0.12		VDDQ/2 + 0.12	V
VOL	Output LOW Voltage	Note 17			VDDQ/2 – 0.12		VDDQ/2 + 0.12	V
VOH(LOW)	Output HIGH Voltage	IOH = −0.1 mA, Nominal Impedance			VDDQ – 0.2		VDDQ	V
VOL(LOW)	Output LOW Voltage	IOL = 0.1 mA, Nominal Impedance			VSS		0.2	V
VIH	Input HIGH Voltage				VREF + 0.1		VDDQ + 0.3	V
VIL	Input LOW Voltage				–0.3		VREF – 0.1	V
IX	Input Leakage Current	GND ≤ VI ≤ VDDQ			−5		5	μA
IOZ	Output Leakage Current	GND ≤ VI ≤ VDDQ, Output Disabled			−5		5	μA
VREF	Input Reference Voltage [18]	Typical Value = 0.75V			0.68	0.75	0.95	V
IDD [19]	VDD Operating Supply	VDD = Max,	333 MHz	(x8)			510	mA
		IOUT = 0 mA,
				(x9)			510
		f = fMAX = 1/tCYC
				(x18)			520
				(x36)			640
			300 MHz	(x8)			480	mA
				(x9)			480
				(x18)			490
				(x36)			600
			250 MHz	(x8)			420	mA
				(x9)			420
				(x18)			430
				(x36)			530

Notes

15.Power up: assumes a linear ramp from 0V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ < VDD.

16.Outputs are impedance controlled. IOH = –(VDDQ/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.

17.Outputs are impedance controlled. IOL = (VDDQ/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.

18.VREF(min) = 0.68V or 0.46VDDQ, whichever is larger, VREF(max) = 0.95V or 0.54VDDQ, whichever is smaller.

19.The operation current is calculated with 50% read cycle and 50% write cycle.

Document Number: 001-00437 Rev. *E Page 20 of 30

[+] Feedback