Side Panels, MDI-Uplink port MDI-X ports | D-Link DES-3224 specs

10/100 Auto Negotiation Switch User’s Guide

The MDI-II port is used as an uplink port for connecting to another switch or for connecting to hubs.

LED Panel

MDI-Uplink port

MDI-X ports

Figure 1: DES-3224 Front Panel

All 24 MDI-X ports on the DES-3224can be used for network connections. You cannot use both the MDI-II Uplink port and port 1x simultaneously. The RS-232 port is located at the rear of the DES-3224.

All LEDs are located on the front panel of the DES-3224. Their purpose is to allow you to monitor the operation and performance of the DES-3224 at a glance.

Side Panels

There are two fans, displayed in

Figure 2, located on the side of the DES-3224. They will come on when the DES-3224 is powered up. There are three holes on each side of the DES-3224. The holes are used for attaching the mounting brackets.

Figure 2: Side Panel

Introduction

3

Image 13

D-Link DES-3224 manual Side Panels, MDI-Uplink port MDI-X ports

Contents

DES-3224 10/100 Auto Negotiation Switch User’s Guide Link Limited Warranty Hardware North, Central, and South America FCC Warning Wichtige Sicherheitshinweise Page Table of Contents Page Page Page Audience About This GuideOrganization Introduction FeaturesFront Panel MDI-Uplink port MDI-X ports Side Panels Management Methods Rear PanelLocal Console Management Telnet Management Updating Firmware Installation Options Installing the DES-3224Unpacking the DES-3224 Desktop/ Shelf Installation Power OnRack Installation Cable Specifications Connecting the DES-3224 to the Network Cable Diagram Cable Requirements MDI-II Port PortsMDI-X Port RS-232 Port DES-3224 to DES-3224 Connection Connecting the DES-3224 to the DES-5024 and Hubs LEDs Power LED Speed/ Link/ Activity LED DES-3224 LED PanelFull/ Half LED Utilization LEDs Local Console Management Managing the DES-3224 ∙ Parity None ∙ Stop bits ∙ Flow Control None Telnet Log ∙ Default User Name D-Link ∙ Default Password D-Link Help Message Help Message Spacebar Switch Port 1-8, 9-16, 17-24 Configuration System ConfigurationSpanning Tree Configuration Console Program Snmp Management Configuration System Configuration MenuVlan Port Management Trunking Port Management Factory Reset to Default Config Values System ResetSoftware Update System Information System Information Menu Boot Prom Firmware VersionHardware Revision Software Version System Description LAN Default GatewaySystem Name System Location System Reset System Reset Factory Reset Factory Reset Factory Reset Confirmation Advantages of Store and Forward System Rate ControlDisadvantages of Store and Forward Disadvantages of Cut-Through Advantages of Cut-Through Software Update Software Update Menu Software Update Transfer Message Displayed as Eeprom is Being Written User Account Change Menu User Account ManagementCreate New User Confirm Password PasswordAccess Level User Name Status Delete Users Delete Old Password Change PasswordNew Password Switch Port Configuration Menu Switch Port ConfigurationState Port State PhysicalPriority Spanning Tree Configuration Menu Spanning Tree ConfigurationSTA Operation Levels Spanning Tree Algorithm Forward Delay TimeBridge Priority Root Cost Root Port Root Bridge Snmp Management Configuration Menu Snmp Management Configuration Access Right Snmp Manager SettingSnmp Community String Authentication Failure Snmp Trap Manager SettingCold Start Link Change EventPage Vlan Port Management Menu Vlan Port Management Vlan Port Management menu New Vlan Name Create/ View VlanPort # TrunkGroup Vlan Name Delete Vlan Menu Virtual LAN Name Modify Vlan Menu Vlan Modify menu Trunking Port Management menu Trunking Port Management Menu New Trunking Group Name Create New Trunking PortName Trunking Port Delete Trunking Port Trunking Port Name Modify Trunking Port Trunking Port Modify menu Problem Solution Troubleshooting Power LED is Off System Error LED Indicators Switch Specifications DES-3224 Technical SpecificationsPort Specifications General EMI Index Access Level User Name 34, 35