Dacor Cabinet Layout, Gas and Electrical Service, Cabinet, Required Dimensions, The installation must allow for the following:

Planning the Installation

Cabinet Layout		Gas and Electrical Service
		• The shaded area shown below denotes the location of the
warning		gas inlet and the electrical junction box/receptacle. This
		is the recommended location. For replacement purposes,
All maximum and minimum cabinet and countertop dimensions		the location of the existing utilities may be utilized provided
and clearances stated in these instructions must be maintained		they do not interfere with the sides or rear of the range.
for safe operation.		Check local building codes for permissible utility connection
• Carefully check the location where the range is to be		locations.
		• An external manual shut-off valve must be installed between
installed. For best performance, the range should be placed
away from drafts that may be caused by doors, windows and		the gas inlet and the range for the purpose of turning on or
heating and air conditioning outlets.		shutting off gas to the appliance.
• To reduce the risk of personal injury and to reduce		The installation must allow for the following:
accumulated smoke in the room, Dacor strongly recommends		• Access to the gas shut-off valve when the unit is installed.
installing a range hood or raised vent (model DR30DI[H]
		• Access to the remote circuit breaker panel or fuse box when
only). A range hood should project horizontally a minimum of
five (5) inches beyond the face of the cabinets.		the range is in place.
• Any openings in the wall behind the appliance or in the floor		• The gas supply piping, gas shut-off valve and the electrical
underneath it must be sealed.		junction box or receptacle must be located so they do not
• Carefully note the requirements stated below for clearances		interfere with the range when it is installed.
		• The junction box and gas shut off valve must be located
to walls and cabinets.
		so that the range can be pulled out for service while the
Cutout tolerances: +1/16” (+1.6 mm), -0		appliance remains connected.
	E
			E	F***

36” (91.4 cm)* 30 1/16” (76.4 cm) 30” (76.2 cm)**

* Recommended ** Minimum

*** See following pages for self-rimming

installations

13” (33.0 cm) max.5

Back wall 1

10” (25.4 cm) min.

30”

(76.2

cm)

F

18”

(45.7 cm)

min.2

to combustible side

min.2,

5

walls above the range

(both sides)

1 Minimum distance to a combustible rear wall for model

Note 3

DR30DI[H] is 2.5” (6.4 cm) from top rear trim. Model DR30D[H]

may be installed flush to rear wall, but non-combusible surface

Suggested

or 9-inch backguard (PN ADB3009) is recommended.

location of

utilities 4

2 Distance to combustible surfaces measured from cooking

Note 6

surface (top of cooktop grate); if installing an overhead

1

range hood, also check the hood specifications for minimum

Minimum distance to a combustible rear wall for model

required clearances.

DR30DI[H] is 2.5” (6.4 cm) from top rear trim. Model DR30D[H]

3 Cabinet/countertop depth is at discretion of customer but

may be installed flush to rear wall, but non-combusible s rface

cabinet face MUST NOT protrude further than rear of

or 9-inch backguard (PN ADB3009) is recommended.

2

cabinet front, see Product Dimensions.

Distance to combustible surfaces measured from cooking

4 Consult local code for exact location requirements.

surface (top of cooktop grate); if installing an overhead

range hood, also check the hood specificationsThisforspecificationminimum does not apply for cabinets located

5

required clearances.

greater than a horizontal distance of 10” (25.4 cm)

3

from the edge of the range.

Cabinet/countertop depth is at discretion of customer but

6 Model DR30D[H]: 37 7/8 (96.2 cm) max.

cabinet face MUST NOT protrude further than rear of

cabinet front, see Product Dimensions.

Model DR30DI[H]: 37 7/16 (95.1 cm) max.

4 Consult local codeCabinetfor xact location requirements.

Required Dimensions

6