Dacor Self-RimmingInstallation Without Raised Vent, and, Top View, Side View, Range With, Model DR30DI, 3 1/4 Inch Side Panels Not Removed

Planning the Installation

Self-Rimming Installation Without Raised Vent

•See page 8 for raised vent installations.

•Only model DR30DI may be installed in a self-rimming configuration. Self-rimming installations create a “built-in” look where the trim of the range overlaps the surrounding countertop. It is also possible, if the cabinets are the right depth, to self rim the front of the range into the cabinet face, immediately behind the control panel and door trim. When the front of the range is self-rimmed, the 3 1/4” side panels are removed.

•When sliding the range into position, it will stop when the rear of the side panels or front panel contacts the notches toward the front of the countertop. The rear of the range trim will overhang the countertop in back.

Model DR30DI	H	J	K
Range With
Countertop Self-	21”	0” (0 cm) to	0” (0 cm) to
Rimmed Only	(53.3 cm)	3 1/4” (8.3 cm)	5 3/8” (13.7 cm)
Countertop and	24 1/4”	NA	0” (0 cm) to
Cabinet Front
	(61.6 cm)		2 1/8” (5.4 cm)
Self-Rimmed 1

1Side panels removed

Countertop height for all self-rimming installations:

35 7/16” (90.0 cm) minimum, 37 7/16” (95.1 cm) maximum

Model DR30DI[H] Countertop Self-Rimmed Only,3 1/4 Inch Side Panels Not Removed

Rear wall or other				10” min.		1/4” min.* (6 mm)
				(25.4 cm)			countertop
vertical surface **
				both sides				overhang
			Combustible side
			wall above range
			29 1/4” (74.3 cm)
			countertop opening
									H
				30” (76.2 cm)
				cabinet opening
				below countertop	J	K
			Notch countertop
		overhang to width of
				cabinets below			To countertop
	Top View			To cabinet face
				below countertop					front

*When increasing overhang, increase dimension H by same amount.

**Any vertical surfaces behind the range must be non-combustible unless countertop overhang exceeds 2 3/4” (7.0 cm).

See Top View for required distance to vertical surfaces

1/4” min. (6.4 mm) Range trim resting

flat countertop min. on countertop

Back of	Countertop	Cabinet face
cutout		Back of
	H
		control
		panel
		3 1/4 inch
		side panel
DR30DI[H] range

Side View

Model DR30DI[H] Countertop and Cabinet Front Self-Rimmed, 3 1/4 Inch Side Panels Removed

Rear wall or other					10” min.		1/4” min.* (6 mm)
					(25.4 cm)			countertop
vertical surface **
					both sides				overhang
			Combustible side
			wall above range
			29 1/4” (74.3 cm)							H
				countertop and
			cabinet opening
		Notch countertop				to	K
					30” (76.2 cm)
	Top View				Cabinet face			To countertop
					below countertop					front

*When increasing overhang, increase dimension H by same amount.

**Any vertical surfaces behind the range must be non-combustible unless countertop overhang exceeds 2 3/4” (7.0 cm).

See Top View for required distance to vertical surfaces

1/4” min. (6.4 mm)

flat countertop min. Range trim resting on countertop

Back of cutout			Countertop
		H			Cabinet face
				Back of control
				panel and trim
				behind door
				rest against
	DR30DI[H] range			cabinet face
	Range side
	panels removed				Side View

7