Danby DPAC8399 owner manual Precaución, Setting the AUTO-ON& AUTO-OFFTIMER

Instrucciones para la instalación del tanque de agua (continúa)

3.Ponga el tanque de agua a la posición correcta sobre la reborde apoyante. Asegúrese de que el conector rápido sobre el tanque de agua está alineado con el conector rápido, instalado a la factoría, localizado al posterior del armario. (véase la figura 37)

Fig.37

4.Para hacer la coneción, empuje el conector del tanque de agua en el conector del armario. Ud. va a oír un chasquido positivo cuando hace la coneción

5.Instale la tapa sobre el tanque de agua.

6.Para desenganchar (desconectar) el tanque de agua externo, apreta el botón de desenganchar que está en la parte superior del conector rápido del armario, pues sujete los mangos de desenganchar localizado por ambos lados del tanque,

levante y tire hacia adelante. (véase la figura 38, 39)

Fig.39

PRECAUCIÓN

Es necesario vaciar el agua acumulada en ambos tanques antes de mover la unidad.

Setting the AUTO-ON & AUTO-OFF TIMER

Before setting the AUTO-ON & AUTO-OFF Timer, the time of day clock must be set/operational. You must also select the appropriate operating MODE. After the appropriate settings have been made, turn off the unit.

1)Press the TIMER-ONkey pad to initiate the AUTO-ONtime sequence. (Fig. 32). The display window will indicate TIMER-ONand the word ON

will flash for 5 seconds. Press the

or key pad to select the desired AUTO-ONstart time. (Fig. 32a).

key pad will decrease the AUTO-TIMEDsetting in 10 minute increments.

keypad will increase the AUTO-TIMEDsetting in 10 minute increments.

When the desired time is established, (the time will flash in the display window) press the CLOCK key pad to register the AUTO TIMER- ON program. The word ON will stop flashing and remain “on”(TIMER ON) indicating the program is set. The time of day clock setting will immediately revert back in the display window.

The unit must remain “OFF” while programming the AUTO-OFF program.

2)Press the AUTO-OFFkey pad to initiate the AUTO-OFFtime sequence. (Fig. 33). The display window will indicate TIMER-OFFand the

word OFF will flash for 5 seconds. Press the

or key pad to select the desired AUTO- OFF time. (Fig. 32a).

key pad will decrease the AUTO-TIMEDsetting in 10 minute increments.

keypad will increase the AUTO-TIMEDsetting in 10 minute increments.

When the desired time is established, (the time will flash in the display window) press the CLOCK key pad to register the AUTO TIMER- OFF program. The word OFF will stop flashing and remain “on”(TIMER OFF) indicating the program is set. The time of day clock setting will immediately revert back in the display window.

IMPORTANT: The desired AUTO-ON & AUTO- OFF time must be registered within a 5 second period (after pressing the TIMER-ON/OFF key pads) otherwise the selected time will not register and the system will automatically revert back to the regular “time of day” clock setting

The unit will start automatically when the specified AUTO-ONtime is achieved on the time of day clock and will stop automatically when the specified AUTO-OFFtime is achieved on the time of day clock. To cancel or override the AUTO-TIMEDprogram, simply turn the unit on or off prior to the scheduled AUTO-ON/OFFtime. You can verify the AUTO-ON/OFFtime selection anytime by pressing each respective TIMER-ON/TIMER-OFFkey pad and the selected time will temporarily appear replacing the time of day clock for approximately

5 seconds.

Fig.38

When the AUTO-ON& AUTO-OFFtimes are set, within the same program sequence, the display window shows TIMER ON OFF identifying that both ON and OFF times are now programmed (Repeatable daily until until such time the program is canceled and/or changed).