Instrucciones para la operación con el control remoto

1.Para enviar una señal: Cuando se enciende la unidad principal

(botón I/O), aparece este símbolo (1A) en la ventana LCD del control remoto. El control remoto debe estar apuntando directamente al tablero de control en la unidad principal cuando se inician los comandos. Cuando se presiona un botón de control remoto (excluyendo los botones Ly R, Reloj y ˚C/˚F), el símbolo “ ” centellea una vez en la ventana LCD del control remoto. Este símbolo confirma que se despachó una señal desde el control remoto y un “Pitido” desde la unidad principal confirma que se recibió la señal. La unidad principal entonces reconocerá y responderá según la selección realizada. Todas las selecciones (excluyendo las graduaciones de la hora del día) aparecerán inmediatamente en la ventana LCD del control remoto y en la ventana LCD de la unidad principal cuando la unidad se encuentre operacional. Es posible que haya una demora pequeña (2 a 5 segundos) antes de que la unidad principal responda a la señal remota. Esto es normal. Si la unidad principal no responde, repita el procedimiento. Si la unidad principal no responde nuevamente:

Chequee lo siguiente:

¿Se encuentran el receptor y la unidad remota dentro de la distancia que se requiere para la operación (7 metros o 23 pies)?

. ¿Está la ventana del receptor en la unidad principal parcialmente bloqueada y/o oscurecida?

. ¿Se han instalado las pilas correctamente dentro del control remoto (positivo + /negativo -)?

. Inspeccione las pilas. Si están agotadas, cámbielas.

2.Graduación del reloj de la hora del día (control remoto): Cuando se instalan las pilas, el reloj indica “0:00” y los dos puntos

centellean (:). Oprima el botón de "Temp/Timer” para graduar la hora corriente del día (0-24 horas). Cada vez que se oprime el botón la graduación de la hora del día va a aumentar o disminuir (incrementos de 1 minuto). Cuando se haya establecido la hora correcta, presione el botón “Set” para activar la graduación del reloj de la hora del día (los dos puntos dejarán de centellear). Para cambiar la graduación del reloj de la hora del día, oprima y sostenga el botón "Clock" (reloj) durante 3 segundos hasta que los dos puntos (:) centelleen. Ajuste la graduación del reloj de la hora del día (botones para graduar la hora) y luego oprima el botón "Set" para activar la graduación del reloj de la hora del día (los dos puntos(:) dejarán de centellear).

NOTA: La graduación del reloj de la hora del día en la unidad de control remoto funciona en forma independiente y no controla la

programar el modo de auto del tablero de control de la unidad principal. En el modo de "auto" la unidad graduará automaticamente el modo de operación según la selección de la temperatura. La unidad principal responderá automaticamente, cambiando entre el modo "Automático-Frío-Calor-Ventilador"para mantener la temperatura programada seleccionada. La deshumidificación no responde/funciona en el modo de "auto".

4. Graduación de la temperatura: Oprima el botón para

seleccionar la temperatura de operación deseada. Cada vez que se oprime el

“Temp/Timer”

botón de temperatura, se aumenta o disminuye la graduación de temperatura

(incrementos de 1˚C, incrementos de 2˚F). La temperatura seleccionada aparecerá en la ventana LCD del control remoto (solamente 17˚C - 30˚C ).

5.Graduación de la velocidad del ventilador: Presione el botón “Fan” en el control remoto para seleccionar la velocidad deseada del operación del ventilador. Dependiendo del modo que se seleccione, cada vez que se oprime el botón, se avanzará a una graduación diferente (Automática-Baja-Mediana-Alta). La velocidad seleccionada del ventilador se visualizará en la ventana LCD del control remoto. Por ej.

MODO

VELOCIDADES del VENTILADOR

COOL (Frio)

Auto/Medium–Low–Medium–High*

HEAT (Calor)

Auto/Medium–Low–Medium–High*

DRY (Seco)

Auto (Medium solamente)

FAN (Ventilador)

Auto/Medium–Low–Medium–High*

(Automática/Mediana-Baja-Mediana-Alta*)

Automática equivale a Mediana (graduación de la velocida del ventilador) en el tablero de control de la unidad principal.

Ventana LCD

3

1A

Energy-Saving Tips

Your Danby appliance is designed to be highly efficient in energy savings. Follow these recommendations for greater efficiency.

1)Select a thermostat setting that suits your comfort needs and leave at that chosen setting.

2)The air filter is very efficient in removing airborne particles. Keep the air filter clean at all times.

3)Use drapes, curtains or shades to keep direct sunlight from penetrating and heating room, but do not allow drapes or curtains to obstruct the air flow around the unit.

Window Installation

Electric Shock Hazard

To avoid the possibility of personal injury, disconnect power to the unit before installing or servicing.

CAUTION

To avoid installation/operation difficulties,

read these instructions thoroughly.

Installation Accessories Fig. 1

Description

Quantity

Flexible exhaust hose with adapters

3/set

stretches from 19 1/2" (50 cm) up to

 

74 3/4" (190 cm)

 

Window exhaust adapter (flat mouth)

1pc

Adjustable window/patio door slider kit

3/set

from 26 5/8" (67.5 cm) up to

 

80" (203 cm)

 

Drain hose connector

1 pc

continuous drain option (hose not included)

 

External Water Tank Accessories Fig. 1a

 

Support Tray & Castor

1 pc

External Tank & Cover

1 pc

Quick Connect (External Tank)

1 pc

SPECIAL NOTE: Exterior drain hose extension (direct drain) is not included with this unit and can be purchased through any local Hardware Store.

4)Start your air conditioner before the outdoor air becomes hot and uncomfortable. This avoids an initial period of discomfort while the unit is cooling off the room. Use of the automatic start/stop programmable TIMER feature can be a major asset in this regard if utilized to the fullest extent.

5)When outdoor temperatures are cool enough, turn the air conditioner off and use the FAN MODE on HIGH, MED or LOW. This circulates indoor air, providing some cooling comfort and utilizes less electricity.

The exhaust/window kit must be installed at all times when the unit is operating under the AIR CONDITIONING mode.

There should be at least 11.8" (30 cm) clearance between the unit and any other objects or building structure. The unit should be installed on a level surface. The window kit does not have to be installed during operation of the remaining three modes. (Heating/Dehumidifying/Fan).

Fig. 1 Installation Accessories

 

Drain Hose Connector

Flexible Exhaust Hose

Window Exhaust

Adapter

19 1/2" - 74 3/4"

 

Adapter

Adapter

Adjustable Window/Patio Door Slider Kit

 

26 5/8" - 80"

Fig. 1a External Water Tank Accessories

graduación del reloj de la hora del día en la unidad principal.

3. La Graduación del modo: Oprima el botón "mode" para graduar

el modo de operación deseada. Cada vez que se oprime el botón

de modo, se graduará a una función diferente (Automático-Frío-

1

4

2

WARNING

When the patio door kit is installed, it will not be

possible to lock the patio door.

Seco-Calor-Ventilador).

NOTA: El modo de "auto" es una característica incorporada que

se activa del control remoto portátil solamente). No puedo

57

THIS COULD POSE A SECURITY RISK!

Installation of a “FOOTBOLT” or “DROP BAR” behind the door is suggested. (Available through most local hardware stores)

Support Tray

Tank & Quick Connect

4

Page 5
Image 5
Danby DPAC8399 owner manual Instrucciones para la operación con el control remoto, Energy-Saving Tips, Modo

DPAC8399 specifications

The Danby DPAC8399 is a versatile portable air conditioner designed to offer efficient cooling and comfort in various living spaces. Ideal for rooms up to 450 square feet, this unit seamlessly blends functionality with convenience, making it a popular choice for homeowners and renters alike.

One of the key features of the Danby DPAC8399 is its impressive cooling capacity of 8,000 BTUs, which ensures a rapid drop in indoor temperatures, providing relief during those sweltering summer months. This model also functions as a dehumidifier, capable of removing excess moisture from the air. With the ability to extract up to 69.5 pints of moisture per day, it helps prevent mold and mildew growth, contributing to a healthier living environment.

The air conditioner comes equipped with a highly efficient, environmentally friendly refrigerant (R410A), ensuring optimal cooling performance while minimizing the impact on the ozone layer. This makes the Danby DPAC8399 not only an effective cooling solution but also an eco-conscious choice for consumers seeking greener alternatives.

A standout feature of this model is its user-friendly electronic controls, complete with an LED display that makes operation straightforward. The included remote control allows users to adjust settings from across the room, providing convenience without the need to get up. With multiple modes available, including cooling, fan, and dehumidifier modes, users can customize their experience to suit their specific comfort needs.

The portable design of the Danby DPAC8399 includes smooth-rolling caster wheels, enabling easy movement from one room to another. Its sleek, compact design ensures it won't take up much space, making it a practical option for apartments or smaller homes. Additionally, the unit comes with a window installation kit for hassle-free setup, enabling users to enjoy cool air almost immediately.

Energy efficiency is another hallmark of the Danby DPAC8399. It features an Energy Efficiency Ratio (EER) rating that emphasizes its low energy consumption, making it an economical choice for cooling throughout the season. This not only helps in reducing utility bills but also contributes to environmental sustainability.

In summary, the Danby DPAC8399 stands out in the world of portable air conditioners with its powerful cooling capabilities, efficient moisture removal, user-friendly controls, and eco-friendly features. Its mobility and compact design make it an ideal cooling solution for a variety of spaces, ensuring a comfortable atmosphere regardless of the outdoor temperatures.