Danby DPAC8399 Instrucciones para la operación del ventilador, Baja-Mediana-Alta, Louvers. Fig

Instrucciones para la operación del ventilador

1)Oprima la tecla I/O (encendido/apagado) para encender la unidad.

2)Oprima la tecla de MODO hasta que la palabra FAN (VENTILADOR) aparezca en la ventana de visualización de cristal líquido (LCD según sus siglas en inglés). Figura 25. Cada vez que se oprima la tecla de MODO, se adelantará a una graduación de modo diferente. (Frío-Seco-Calor-Ventilación).No hay ninguna luz indicadora de modo visible durante el funcionamiento del modo de VENTILADOR (esto es normal).

3)Oprima la tecla FAN (VENTILADOR) para seleccionar la graduación de velocidad (FAN SPEED) del ventilador que se desea. Figura 26. Su selección aparecerá en la ventana LCD. Cada vez que se oprima la tecla del ventilador, se alternará entre las diferentes graduaciones de velocidad del ventilador

(Baja-Mediana-Alta).

No hay luz Modo de ventilador

Fig. 25

Velocidad del
ventilador	Fig. 26

Air Conditioner Operating Instructions (cont’d)

5) Press the FAN key to select the desired fan

speed setting (Low-Med-High). See Fig. 14.

Your selection will be displayed in the LCD

window (each depression of the fan key will

advance to a different setting).

6) Press the SWING key to activate the automatic

air swing (oscillating) feature (the “air swing”

symbol will appear in the LCD window). Fig. 15.

To deactivate the air swing feature, press the

SWING key again.

7) Condensed water will be accumulated in the

water tank. When the tank is full, the unit will

sound a signal (8 beeps) and the Water Full

indicator light start flashing. At this time the air

conditioning process will immediately stop.

However, the fan motor will continue to operate

(this is normal). Carefully remove the water tank

from the cabinet and dispose of the water.

Fan Speed

Fig. 14

4)Oprima la tecla SWING (OSCILACIÓN) para activar la opción de oscilación automática de aire (el símbolo “air swing” aparecerá en la ventana LCD). Figura 27. Para desactivar la opción de oscilación de aire, oprima nuevamente la tecla SWING.

Oscilación	Fig. 27
del aire

5)Para ajustar la dirección de la corriente de aire (hacia arriba/hacia abajo solamente), ajuste cualquiera de las láminas horizontales tipo persiana (excluyendo la lámina superior e inferior), y las láminas restantes se ajustarán automáticamente a la posición determinada. Figura 28.

Fig. 28

Replace the water tank back to it’s original

position (in cabinet) and the air conditioning

process will automatically resume. It may take

3-5 minutes for the compressor to re-start. This

is normal.

8) To adjust “air flow” direction, (up / down only)

adjust any one of the Horizontal Louver Blades

(excluding the top or bottom louver) and the

remaining louvers will automatically adjust to the

set position (excluding the top and/or bottom

louvers). Fig. 16.

Cooling stops automatically when the set temperature is achieved. Cooling resumes when the room temperature rises above the set temperature level. The temperature has no effect on the fan operation. Therefore, the fan will operate continuously (after the compressor has cycled off) to maintain optimal temperature control.

CAUTION

During air conditioning and dehumidifying modes, if the compressor cycle is interupted (unplugged, power failure,etc.) and reinstated immediately thereafter, (within 3-5 minutes) a “compressor protection circuit” is automatically self-affected. The mode indicator light will flash “green” for approximately 10 seconds, confirming the protection circuit is activated. The compressor cannot operate during a “compressor protecton” condition. (this is normal) It may take 3-5 minutes before the “protection circuit” self-deactivates.

DO NOT ATTEMPT TO START THE UNIT (COMPRESSOR) DURING THIS PERIOD. Upon re-starting the unit (turn 1/0 switch on) all program information(i.e. time, mode, fan speed, auto

Air Swing

Fig. 15

Fig. 16

ATTENTION

Removal and/or partial displacement of the water tank will cause the compressor to stop operating (this is a safety feature). This condition will cause the unit to “beep 8 times” and the “water full” light will flash (red) continuously until corrected. The compressor cannot operate during a flashing “red” light condition. Check the following;

1.Is the water tank full?

Empty and re-install water tank.

2.Has the water tank been accidently displaced? Re-position water tank.

The “red” light will stop flashing automatically when the water tank has been emptied and/or

correctly re-positioned.