
Installing/Setting the Speakers
sSet the “Amp Assign” Mode According to the Speaker Layout
The signals output from the
Amp assign mode | SURR. BACK/AMP ASSIGN | Example of speaker installation | |||||||
(vpage 28) | Speaker connections | ||||||||
|
|
|
|
|
|
| |||
Normal | Surround back |
|
|
|
|
|
|
| |
speakers |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
| (7.1) |
|
| ||
|
|
|
|
|
|
|
|
| |
| Surround back |
|
|
|
|
|
|
| |
| speakers |
|
|
|
|
|
|
| |
Normal | b Connect to the “L” speaker |
|
|
|
|
|
|
| |
terminal. |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
| b Set “S.Back” (vpage 29) |
|
|
|
|
|
|
| |
| to “1spkr”. |
|
|
|
|
|
|
| |
|
|
|
| (6.1) |
|
| |||
|
|
|
|
|
|
|
|
| |
| Not connected |
|
|
|
|
|
|
| |
Normal | b Set the “S.Back” setting |
|
|
|
|
|
|
| |
(vpage 29) to “None”. |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
| (5.1) |
|
| ||
|
|
|
|
|
|
|
|
| |
Front Height | Front Height |
|
|
|
|
|
|
| |
speakers |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
| (7.1) |
|
| ||
|
|
|
|
|
|
|
|
| |
| Front A or B |
|
|
|
|
|
|
| |
Front A | speakers |
|
|
|
|
|
|
| |
b For connections, see |
|
|
|
|
|
|
| ||
or |
|
|
|
|
|
|
| ||
“About |
|
|
|
|
|
|
| ||
Front B |
|
|
|
|
|
|
| ||
(vpage 13). |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
| (5.1) |
|
| ||
|
|
|
|
|
|
|
|
| |
|
| MAIN ZONE | ZONE2 | ||||||
ZONE2 | ZONE2 |
|
|
|
|
|
|
| |
(Default) | speakers |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |||
|
|
|
|
|
| (2) |
| ||
|
|
| (5.1) |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
ENGLISH
Connecting the Speakers |
|
|
|
|
| Getting | ||||||
Subwoofer with | Front speakers |
|
| Front speakers | Center | Surround | ||||||
|
| Started | ||||||||||
|
| A |
|
| B |
| speaker | speakers | ||||
|
|
|
|
|
| |||||||
| (L) | (R) |
|
| (L) | (R) |
|
| (L) | (R) | Connections | |
|
|
|
|
|
| |||||||
|
|
| w | q |
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| ||
| w | q | w | q | w | q | w | q | w | q w | q | Settings |
*/ |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| Playback |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| Control Remote |
|
|
|
|
|
|
| For connections of the SURR. BACK/AMP | Information | ||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
| ASSIGN speaker terminals, see “Amp Assign” |
| ||||
|
|
|
|
|
|
| (vpage 28). |
|
|
| Troubleshooting | |
etc., or the ± sides touch each other, the protection | and the protection circuit might be activated. The | |||||||||||
Protection circuit |
|
|
|
|
|
|
|
|
|
|
| |
If the core wires touch the rear panel and the screws | specified (eg, 4 Ω/ohms), the temperature will rise, |
| ||||||||||
circuit will be activated and the power indicator will | power supply will go into the standby state, and the | Specifications | ||||||||||
flash red at intervals of 0.5 secs. |
|
|
| power indicator will flash red at 2 second intervals. | ||||||||
|
|
|
| |||||||||
If the protection circuit is activated, the speaker | In this case, please switch off the power supply, and |
| ||||||||||
output is isolated, and the power supply goes to | wait until the |
| ||||||||||
the standby state. If the power supply is turned off, | surrounding ventilation is good. |
|
|
| ||||||||
after the power supply cord is withdrawn, please | Even if there are no problems with the surrounding |
| ||||||||||
confirm that speaker cable and input cable are | ventilation and connections, in the event of the |
| ||||||||||
connected. |
|
|
|
|
|
| protection circuit becoming activated, due to |
| ||||
Also, if replaying | large sound levels | by | using | thinking that the |
| |||||||
a speaker having | an | impedance | less | than that | contact DENON Service center after switching off. |
|
12