Denon AVR-2310CI Different Speakers, Adjust the Volume of the, Various Memory Functions

ENGLISH

Getting		Adjust the Volume of the
		Different Speakers
Started
		You can adjust the channel level either according to the playback
Connections		sources or to suit your taste, as described below.
	1					C e n t e r		0 . 0 d B
		Adjust the volume of the different speakers
			Press	.	C H A N N E L L E V E L
						F r o n t L		0 . 0 d B
Settings						F r o n t R		0 . 0 d B
						S u b w o o f e r		0 . 0 d B
						S u r r o u n d R		0 . 0 d B
						S . B a c k R		0 . 0 d B
						S . B a c k L		0 . 0 d B
						S u r r o u n d L		0 . 0 d B
						F a d e r		F r o n t R e a r
Playback							S e l e c t
								Front
			Press uito select the speaker.
-Multi
		2time one of the buttons is pressed.
			The speaker that can be set switches each
Zone
		3Press opto adjust the volume.
Remote
		bIn the case of a subwoofer, reducing the volume when it is at
Control		“–12 dB” will change the setting to “OFF” (none).
		If headphones are plugged in, the headphones						settings screen
Information
		Adjusting the volume of groups of speakers
		appears.
Troubleshooting		(Fader Function)
		This function lets you adjust (fade) the sound from all the front (Front
		speaker / center speaker / Front Height speaker) or rear (Surround speaker /
		Surround Back speaker) speakers at once.
			Use	or i to select “Fader”, then select the item
Specifications		1 to be adjusting using oor p.
		2Press opto adjust the volume of the speakers.

•The fader function does not affect the subwoofer.

•The fader can be adjusted until the volume of the speaker adjusted to the lowest value is –12 dB.

Saving Frequently Used Settings (Quick Select Function)

This function allows you to save all the settings shown in step

1.When frequently used settings are saved, they can easily be set again the next time you want to use them. This function also allows you to always enjoy the same playback environment.

• Three sets of settings can be saved.

MAIN ZONE settings

Saving the settings

1 Set the items below to the settings you want to save.

q Input source (vpage 42) w Input Mode (vpage 39) e Surround Mode (vpage 46)

r Audyssey Settings (MultEQ, Dynamic EQ, Dynamic Volume) (vpage 50)

t Front Speaker Setup (vpage 30) y Volume setting (vpage 42)

u Video select (vpage 38)

2Press and hold the desired until “Memory”

appears on the display.Front

The current settings will be memorized.

GQuick Select DefaultsH

	Input Source	Volume
Quick Select 1	DVD	–40 dB
Quick Select 2	SAT/CBL	–40 dB
Quick Select 3	VCR/iPod	–40 dB

Calling the settings out

	Front
Press the	at which the

settings you want to call out are saved.

NOTE

Input sources stored with the quick select function cannot be selected if they have been deleted at menu “Source Delete” (vpage 33). In this case, store them again.

nNaming Quick Select settings

“Quick Select Name” (vpage 34).

ZONE2 settings

It is also possible to save three settings for ZONE2.

Saving the settings

1Set the remote control unit’s device selector switches as shown on right.

2Performsettings”. steps 1 and 2 under “MAIN ZONE

Various Memory Functions

Personal Memory Plus Function

This function sets the settings (input mode, surround mode, HDMI output mode, MultEQ, Dynamic EQ, Dynamic Volume, audio delay etc.) last selected for the individual input sources.

The surround parameters, tone settings and the volumes of the different speakers are stored for the individual surround modes.

Last Function Memory

This stores the settings as they were directly before the standby mode was set.

When the power is turned back on, the settings are restored to as they were directly before the standby mode was set.

Backup Memory

The various settings are backed up for about 1 week, even if the power is turned off or the power cord is disconnected.

55