Restoring All the Settings to as They were at the Time of Purchase (Resetting the Microprocessor)

Perform this procedure if the display is abnormal or if operations cannot be performed.

When the microprocessor is reset, all the settings are reset to their default values.

1 Turn off the power using

on the main unit.

2Press while simultaneously pressing and on the main unit.

3Once the display starts flashing at intervals of about 1 second, release the two buttons.

If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.

Specifications

nAudio section

• Power amplifier

Rated output:

Front (A, B):

 

 

105

W+105 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)

 

135

W+135 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)

 

Center:

 

 

105

W

(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)

 

135

W

(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)

 

Surround:

 

 

105

W+105 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)

 

135

W+135 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)

 

Surround Back:

 

 

105

W+105 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)

 

135

W+135 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)

Output connectors:

Front:

A or B

616 Ω/ohms

 

 

A + B

1216 Ω/ohms

 

Center, Surround, Surround Back / Amp Assign:

 

 

 

616 Ω/ohms

• Analog

 

 

 

Input sensitivity / Input impedance:

200 mV / 47 kΩ/kohms

 

Frequency response:

10 Hz ~ 100 kHz — +1, –3 dB (DIRECT mode)

S/N:

100 dB (IHF-A weighted, DIRECT mode)

 

 

 

 

 

ENGLISH

nVideo section

1 Vp-p, 75 Ω/ohms

 

 

 

Getting

 

 

 

Input / output level and impedance:

 

 

 

• Standard video connectors

 

 

 

 

 

 

Frequency response:

5 Hz ~ 10 MHz — +1, –3 dB

 

 

 

Started

Input / output level and impedance:

Y (brightness) signal — 1 Vp-p, 75 Ω/ohms

 

 

 

S-Video connectors

 

 

 

 

 

 

 

C (color) signal — 0.286 Vp-p, 75 Ω/ohms

 

 

 

Connections

Frequency response:

5 Hz ~ 10 MHz — +1, –3 dB (when video convert set to “OFF”)

 

 

 

• Color component video connector

 

 

 

 

 

 

Input / output level and impedance:

Y (brightness) signal — 1 Vp-p, 75 Ω/ohms

 

 

 

 

 

PB / CB signal — 0.7 Vp-p, 75 Ω/ohms

 

 

 

 

 

PR / CR signal — 0.7 Vp-p, 75 Ω/ohms

 

 

 

 

Frequency response:

5 Hz ~ 60 MHz — +0, –3 dB (when video convert set to “OFF”)

 

Settings

nTuner section

(note: µV at 75 Ω/ohms, 0 dBf = 1 x 10-15W)

 

 

 

 

[FM]

[AM]

 

 

Receiving Range:

87.5 MHz ~ 107.9 MHz

520 kHz ~ 1710 kHz

Playback

 

23 µV (38.5 dBf)

18 µV

 

Usable Sensitivity:

1.0 µV (11.2 dBf)

 

 

50 dB Quieting Sensitivity:

1.6 µV (15.3 dBf)

 

 

 

 

S/N (IHF-A):

77 dB

 

 

 

 

Multi

 

72 dB

 

 

 

 

Total harmonic Distortion (at 1 kHz):

MONO

0.15 %

 

 

 

 

STEREO

0.3 %

 

 

 

-

 

 

 

 

Zone

nGeneral

 

 

 

 

 

 

 

 

 

 

 

Power supply:

AC 120 V, 60 Hz

 

 

 

Remote

Power consumption:

6.0 A

 

 

 

 

 

 

 

 

 

 

0.3 W (Standby)

 

 

 

 

Maximum external dimensions:

434 (W) x 171 (H) x 377 (D) mm (17-3/32” x 6-47/64” x 14-27/32”)

 

Control

Weight:

11.3 kg (24 lbs 14.6 oz)

 

 

 

 

 

 

 

nMain Remote control unit (RC-1117)

 

 

 

 

 

Batteries:

R6/AA Type (two batteries)

 

 

 

Information

Maximum external dimensions:

52 (W) x 243 (H) x 21 (D) mm (2-3/64” x 9-9/16” x 53/64”)

 

 

 

Weight:

184 g (Approx 6.5 oz) (including batteries)

 

 

 

 

nSub Remote control unit (RC-1119)

 

 

 

 

 

Batteries:

R03/AAA Type (two batteries)

 

 

 

 

Maximum external dimensions:

50 (W) x 211 (H) x 22 (D) mm (1-31/32” x 8-5/16” x 55/64”)

 

Troubleshooting

Weight:

110 g (Approx 3.9 oz) (including batteries)

 

 

 

 

 

 

 

z For purposes of improvement, specifications and design are subject to change without notice.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Specifications

 

 

 

 

 

 

 

70