Denon AVR-4800 manual Learning function

Learning function

•If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can “teach” the AVR-4800’s remote control to “learn” the codes from the component’s original remote control.

•The buttons that can be “learned” are the CD, DECK and MD system buttons (see page 32) and the DVD, VDP, VCR and TV/DBS system buttons (see page 35). (For the CD, MD, DVD, VDP and TV/DBS, the A block buttons can also be “learned”, and for the DVD and TV/DBS, the B block buttons can also be “learned”.)

1	Press the USE/LEARN selector button with the tip of a pen
	etc., to set the learn mode. Both the START and LEARNED/TX

indicators flash. Flashes

	This unit’s remote
	control unit flashes
2	Set the program switch to the side to be “learned”.
	Set to the AUDIO side for the CD, tape deck or DAT position,

to the VIDEO side for the VDP, VCR or TV position.

AUDIO

A

2

1,8

SET	CALL	OFF	ON / SOURCE
DVD	VDP	TUNER	SHIFT
1	2	3
TV/DBS	V.AUX	PHONO
4	5	6
VCR-1	CD	MD / TAPE-1	CHANNEL
7	8	9
VCR-2	0	TAPE-2 MON	TV/VCR
+10			A / B
VOLUME			DISC SKIP+
	DOLBY / DTS
HOME THX CINEMA	SURROUND	DIRECT
DSP SIMULATION	5CH / 7CH STEREO	STEREO
			MASTER VOL.
INPUT MODE	ANALOG	EXT.IN
AUDIO	DECK MD
	CD	MULTI	MUTING

AVR/AVC	VIDEO	DVD	TV
		VDP	VCR

	SYSTEM	SURROUND
TUNING	SETUP	PARAMETER
BAND	TITLE	MENU/GUIDE
		CH SELECT
MODE		ENTER
		SELECT
MEMORY	STATUS	ON SCREEN
	DISPLAY	RETURN
USE/LEARN T.TONE	MULTI	SPEAKER DVD
		SET UP

4

3

B

			5	Check that the START LED is lit, then press the button to be
	AVR/AVC	VIDEO		“learned” on the other remote control unit.
3	Set the program switch to the position to be “learned”.			Other remote
	DECK	MD		control unit
	CD	MULTI
	DVD	TV
	VDP	VCR
				This unit’s remote
				control unit flashes
4	Set the remote control units so they are facing each other,		6	Once the START LED turns off and the LEARNED/TX LED
	then press the button to be “learned” on this unit’s remote
	control unit.			lights, release the button on the other remote control unit.

Transmitting windows	Other remote
	control unit
Lit

	Approx.
This unit’s remote	5 cm
control unit flashes

The indicator stops flashing and the START LED lights.

The learnable buttons are the buttons which can be operated with the DENON system codes for the CD player, DAT and tape deck, the buttons which can be operated with the preset memory for the VCR, VDP and TV. For the TV only, however, the buttons in the section indicated “A” on the diagram above can also be “learned”. Use these to “learn” TV channels.

	The two LEDs start
	flashing again.	Lit
7	To “learn” other buttons, repeat steps 2 to 6.
8	Once the learning operation is completed, press the
	USE/LEARN selector button again.
	The two LEDs stop flashing and the learning mode is

cancelled.

Check that the stored codes work properly.

NOTES:

•Up to 26 codes can be “learned”, but this number may be lower if the codes are long.

•If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s) is released.

•If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes cannot be stored in RC-869.

•If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just attempted to store was not stored.

To “learn” that code, first perform the resetting operation. (See page 39.)

36