Denon AVR-4800 manual Connections, Connecting the audio components, Connecting a turntable

5 CONNECTIONS

•Do not plug in the AC cord until all connections have been completed.

•Be sure to connect the left and right channels properly (left with left, right with right).

•Insert the plugs securely. Incomplete connections will result in the generation of noise.

•Use the AC OUTLETS for audio equipment only. Do not use them for hair dryers, etc.

•Note that binding pin plug cords together with AC cords or placing them near a power transformer will result in generating hum or other noise.

•Noise or humming may be generated if a connected audio equipment is used independently without turning the power of this unit on. If this happens, turn on the power of the this unit.

Connecting the audio components

• When making connections, also refer to the operating instructions of the other components.

OUTPUT		CD player
R	L

R L

Connecting a turntable

Connecting a CD player

Connect the CD player’s analog output jacks (ANALOG OUTPUT) to this unit’s CD jacks using pin plug cords.

Pre-main (integrated) amplifier for multi-source playback

B

Connect the turntable’s output cord to the AVR-

Turntable

Connecting the pre-out jacks

4800’s PHONO jacks, the L (left) plug to the L

jack, the R (right) plug to the right jack.

(MM cartridge)

Use these jacks if you wish to connect external power amplifier(s) to

increase the power of the front, center and surround sound channels, or

NOTE:

for connection to powered loudspeakers. For instructions on using the

This unit cannot be used with MC cartridges

effect output, refer to page 44.

directly. Use a separate head amplifier or

Connecting the AC OUTLETS

step-up transformer.

AC OUTLETS

• SWITCHED

If

humming

or other noise is

(total capacity – 120 W (1 A.))

generated when the ground wire

The power to these outlets is turned on and off in conjunction with the POWER

Ground wire

switch on the main unit, and when the power is switched between on and

is

connected, disconnect the

standby from the remote control unit.

ground wire.

No power is supplied from these outlets when this unit’s power is at standby.

Never connect equipment whose total capacity is above 120 W (1 A.)

NOTE:

Only use the AC OUTLETS for audio equipment. Never use them for hair dryers,

TVs or other electrical appliances.

AC cord

AC outlets (wall)

AC 120V, 60Hz

(Supplied)

Extension jacks for future use

R

L

R

L

IN

MULTI

MONITOR

R

FRONT

L

R

SURROUND

FM

PHONO

SOURCE

/ EFECT, SB

A

L

OUT-1

COAX.

R

OUT

Y

CB

CR

Y

CB

CR

Y

CB

CR

75

L

MONITOR

IN

DVD

IN

TV/DBS

MONITOR

OUT

SIGNAL CD

FRONT

OUT-2

COMPONENT VIDEO

GND

CENTER

SB-R

SB / SB-L

LOOP

ROOM TO ROOM

DVD

SUB

DVD

ANT.

WOOFER

REMOTE

IN

A M

IN

CONTROL

R

VDP

SURROUND

VDP

OUT

ANTENNA TERMINALS

TV /

EFECT

TV /

POWER

DBS

/ SB

SB/

DBS

AMP

SB-R

FRONT / EFECT, SB / CENTER: 6

16

V.AUX

SB-L

V.AUX

REMOTE CONTROL

PRE OUT

R

L

SURROUND / A OR B

: 6

16

6CH EXT. IN

A+B

: 8

16

SPEAKER SYSTEMS

B

FR

FL VCR-1

VCR-1

VCR-1

AC IN

R

L

SURROUND

OUT

R

L

SW

C

VCR-2

VCR-2

R

L

VCR-2

OPTICAL

OPTICAL-5

R

COAXIAL

SL MD /

MD /

OUT

IN

1

2

3

4

IN

OUT

IN

SR

VCR-1

1

2

3

L

TAPE-1

TAPE-1

SWITCHED TOTAL 120W(1A.) MAX.

ER

EL TAPE-2

TAPE-2

VCR-2

AC 120V

60Hz

8CH EXT. IN

R

AUDIO

VIDEO

S-VIDEO

DIGITAL

AC OUTLETS

L

R

L

Route the connection cords, etc., in such a way that

they do not obstruct the ventilation holes.

R

R

Tape deck 2

MD recorder, DAT deck or other component

L

L

equipped with digital input/output jacks

							B
R	L	R	L			OUTPUT	INPUT
OUTPUT		INPUT
Connecting a tape deck						OPTICAL
Connections for recording:							CD player or other component equipped
Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s					OPTICAL	COAXIAL
tape recording (OUT) jacks using pin plug cords.							with digital output jacks
					OUTPUT
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s
tape playback (IN) jacks using pin plug cords.						Connecting the DIGITAL jacks
OUTPUT		INPUT		Tape deck 1 or MD recorder		Use these for connections to audio equipment with digital output.
R	L	R	L			Refer to page 28 for instructions on setting this terminal.
R	L	R	L			NOTES:
						• Use 75 Ω	/ohms cable pin cords for coaxial connections.
						• Use optical cables for optical connections, removing the cap
						before connecting.

6