SUN VALLEY STOVE COMPANY

CAST IRON STOVE AND BURNER SYSTEM

STOVE AND B-VENT BURNER SYSTEM INSTALLATION

Continued

INSTALLING OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1, GWMS2

WARNING: Installation must be done by a qualified installer familiar with low voltage wiring procedures.

WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or fire hazard will occur.

1.Open lower door panel. The valve is attached to the underside of the fire- box assembly.

2.Disconnect from the valve the wires running from the ON/OFF switch.

3.Connect one terminal of the wire for the wall thermostat to the THTP termi- nal on the valve. Connect remaining wire terminal to the TH terminal on the valve. Make sure that the wire termi- nals are in the positions on the unit as pictured in Figure 36. If wires are not connected as shown the thermostat will not work.

4.Route the wire to a convenient loca- tion to mount your thermostat (no out- side wall). IMPORTANT: The wire must not exceed 25 feet in length.

The thermostat should be mounted 54" above the floor in a location where there is good air circulation. Avoid heat sources such as lamps, direct sun- light, fireplace, or heat and air condi- tioning ducts.

5.Gently remove the cover of the ther- mostat from the base. Grasp the sides of the cover firmly and pull to separate from the base.

6.Feed the electrical wires through the rectangular slots (from the back) on each side of the base (see Figure 37).

WARNING: Do not connect this thermostat to a power source. Electrical shock and/or fire hazard will occur.

7.Connect one bare wire end to each ter- minal (“W” and “R”) of the thermostat base (see Figure 38).

8.Install the base to the wall with screws provided with thermostat.

9.Move the temperature adjustment back and forth to insure the bimetal is free from restrictions.

10.Replace the cover onto the base. (Upon installation, the thermostat must be al- lowed to stabilize at room temperature for a minimum of 30 minutes for proper operation.)

11.Set the temperature adjustment to the desired setting. This thermostat has been electronically calibrated at the factory. No adjustment or leveling is necessary.

Feed wires through rectangular slots

Figure 37 - Back View of Thermostat Base

Terminal “W”

W

Terminal “R”

R

INSTALLING OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIES - GHRC AND GHRCTA SERIES

NOTICE: Only use alkaline bat- teries (not included).

Installing Remote Receiver

1.Open bottom door on stove body and locate the switch plate on the left of the valve bracket.

2.Disconnect wires from THTP and TH on control valve that lead to the switch (see Figure 36, page 15). Discard switch plate, screws, and nuts.

3.Install 9-volt battery (not included) into receiver battery clip and connect to ter- minals (see Figure 39).

4.Place receiver into valve bracket and align holes (see Figure 40).

5.Use push-in fasteners included with receiver to secure to bracket.

6.Connect the wires from the receiver to the valve at TH and THTP (see Figure 36, page 15).

Receiver

Terminal

Wires

Battery Clip

9-Volt Battery

Figure 39 - Installing Battery in Receiver

LO

H

I

OFF

L

 

P

 

I

ON

O

T

Figure 40 - Installing Remote Receiver

Figure 38 - Thermostat Base Terminal “W” and “R”

For more information, visit www.desatech.com

16

106706

Page 15 Page 17
Page 16
Image 16
Desa MSRBVN, MSRBVP installation manual Installing Optional Wall Mounted Thermostat GWMT1, GWMS2, Installing Remote Receiver
Page 15 Page 17

MSRBVP, MSRBVN specifications

Desa MSRBVN and MSRBVP are two innovative residential community projects that have garnered attention for their design, sustainability, and technological integrations. These developments aim to cater to the growing demand for modern living spaces that balance comfort, efficiency, and environmental responsibility.

One of the main features of Desa MSRBVN and MSRBVP is their careful urban planning. These communities provide an array of housing options, from single-family homes to multi-unit residences, ensuring that there is something for everyone, including families, young professionals, and retirees. The layouts are designed to maximize natural light and airflow, creating a pleasant living environment.

Sustainability is a cornerstone of both projects. The communities incorporate green building practices that reduce their carbon footprint. This includes the use of energy-efficient materials, solar panels for renewable energy generation, and greywater recycling systems that help manage water resources effectively. Landscaping is also thoughtfully designed, with native plants that require minimal irrigation and support local biodiversity.

Technologically, Desa MSRBVN and MSRBVP are at the forefront of smart living. Each home is equipped with advanced home automation systems, allowing residents to control lighting, heating, and security features remotely. Integration with mobile applications provides users with seamless access to their home systems, enhancing convenience and safety.

Safety and community are also pivotal aspects. These developments include well-lit public spaces, walking paths, and recreational areas that encourage outdoor activities and social interaction. Security measures, such as gated entries and surveillance systems, ensure that residents feel secure within their community.

In terms of connectivity, both Desa MSRBVN and MSRBVP benefit from strategic locations that offer easy access to public transportation, shopping centers, schools, and healthcare facilities. This makes daily commutes and lifestyle requirements more manageable for residents.

Overall, Desa MSRBVN and MSRBVP exemplify the future of residential living, where thoughtful design, sustainability, and technology converge to create vibrant and connected communities. As urban areas continue to evolve, such projects highlight the importance of integrating modern living solutions that prioritize residents' well-being and environmental stewardship.
Top Page Image Contents