Wall Switch Installation

VENTING INSTALLATION

Parts Lists for Venting Kits and Components (Cont.)

INSTALLATION

Wall Switch Installation

VENTING INSTALLATION

Continued

Vanguard Rigid Venting (Cont.)

Number	Description
D1000	7" x 12" Galvanized Coaxial Pipe (6 pcs.)
D1010	7" x 24" Galvanized Coaxial Pipe (6 pcs.)
D1020	7" x 48" Galvanized Coaxial Pipe (6 pcs.)
D1030	7" Adjustable (7-12") Galvanized Coaxial Pipe
	(6 pcs.)
D1050	7" x 6" Galvanized Coaxial Pipe (6 pcs.)
D2000	7" x 90° Elbow (6 pcs.)
D2010	7" x 45° Elbow (6 pcs.)
D2060	7" x 45° Starter Elbow
D3000 Wall Strap/Offset Support (6 pcs.)
D3010	Storm Collar (6 pcs.)
D3020	Wall Thimble (6 pcs.)
D3050	Vertical Restrictor (6 pcs.)
D3060	Ceiling Firestop/Support (6 pcs.)
D3070	Rectangular Horizontal Rigid Vent Termination Cap
D3090	Cathedral Ceiling Support Box
D4000	Roof Flashing 6/12-9/12
D4010	Roof Flashing 9/12-12/12
D4020	Flex Connector (6 pcs.)
D4030	Flex Wall Thimble (6 pcs.)
D4040	4" Hose Clamp (6 pcs.)
D4050	7" Hose Clamp (6 pcs.)
D5000	Vinyl Siding Standoff (6 pcs.)

Vanguard Flexible Venting

Number	Description
FGFVK	Flex Ground Floor Vent Kit
	Includes: Flex Adapter, 7" x 4' Flexible Pipe, 4" x 4'
	Flexible Pipe, Wall Thimble, Horizontal Termination,
	(4) Spacer Springs, (2) 4" Hose Clamps, (2) 7" Hose
	Clamps, RTV Silicone, and 10 Screws
D1040	7" x 25' Coaxial Flex Pipe with Spacer Springs
D3080	Rectangular Horizontal Flex Termination Cap

Simpson Dura-Vent GS 4" x 6 5/8 "

Number Description

9027" x 48" Pipe

9037" x 36" Pipe

9047" x 24" Pipe

9067" x 12" Pipe

9077" x 9" Pipe

9087" x 6" Pipe

Simpson Dura-Vent GS 4" x 6 5/8 " (Cont.)

Number Description

9117" Adjustable (11"-14 5/8") Pipe

940Wall Thimble

941Cathedral Ceiling Support Box

943Roof Flashing 0/12-6/12

943S Roof Flashing 7/12-12/12

9457" x 45° Elbow

950Vinyl Siding Standoff

953Storm Collar

963Ceiling Firestop

98136" Snorkel Termination

984Horizontal Termination Vent Cap

988Wall Strap

9907" x 90° Elbow

991Vertical High Wind Termination

INSTALLATION

Since the VDVF36 series models use a valve that operates on millivolt current generated by the pilot, a wall switch may be used to activate the gas control valve without the use of normal household electricity.

1.To remove the louvers, simultaneously pull both top end spring latches towards the center of the appliance until they are dis- engaged from locating holes. Repeat for bottom end spring latches and pull outward. Reverse the procedure to install lou- vers back onto the appliance (see Figure 32).

Glass

Locating