Desa VDVF36STN/STP Lighting Instructions, Optional Remote Operation, To Turn OFF GAS To Appliance

OPERATING FIREPLACE

Continued

LIGHTING

INSTRUCTIONS

1.	STOP! Read the safety information in column 2, page 22,
	before proceeding.
2.	Set the “HI-LO” knob to the lowest setting.
3.	Turn off all electrical power to the appliance.
4.	Open control access panel.
5.	Push in gas control knob slightly and turn clockwise
	to “OFF”.
6.	Wait five (5) minutes to clear out any gas. Then smell for
	gas, including near the floor. If you smell gas, STOP! Fol-
	low “B” in the safety information in column 2, page 22. If
	you don’t smell gas, go to the next step.
7.	The pilot is located by the main burner.
8.	Turn knob on gas control counterclockwise	to
	“PILOT”.
9.	Push in the control knob all the way and hold in. Immedi-
	ately light the pilot by pressing the ignitor button until a
	flame appears one (1) minute after the pilot is lit. Release
	knob and it will pop back up. Pilot should remain lit. If it
	goes out, repeat steps 5 through 9.
	• If knob does not pop out when released, stop and call gas
	supplier.
	• If the pilot will not stay lit after several tries, turn gas
	control knob to “OFF” and call your service technician
	or gas supplier.
10.	Turn gas control knob counterclockwise	to “ON”.
	Knob can be turned to “ON” only if the control knob is
	popped out.

OPERATING FIREPLACE	23
Lighting Instructions
To Turn Off Gas To Appliance
Optional Remote Operation

3.Remove control access panel.

4.Push in gas control knob slightly and turn clockwise to “OFF”. Do not force.

5.Replace control access panel.

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must be purchased sepa- rately (see Accessories, page 29). Follow instructions included with the remote control.

NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instruc- tions, page 22.

1.After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position. Note: The burners may light if hand-held remote ON button was on when selector switch was last turned off. You can now turn the burners on and off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch in the RE- MOTE position when the pilot is not lit. This will drain the battery.

IMPORTANT: Be sure to press the ON/OFF buttons on the hand-held remote control unit for up to 3 seconds to assure proper operation.

2.Press ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit.

11.	Set “HI-LO” knob to desired setting.
12.	Turn on all electric power to the appliance.

Gas Control Knob			HI/LO Knob
Position Indicator			O
			IL	T
			P
	N		16AI
	O
O	T				TH
				7
I
L
P		L	I
	FFO	O	H		TP
	E A				TPTH

Figure 50 - Control Knob in the PILOT Position

TO TURN OFF GAS

TO APPLIANCE

Piezo Ignitor

Thermocouple

Figure 51 - Pilot

Flame Adjustment Knob

ON

OFF

REMOTE

Pilot Burner

Thermopile

Control Knob in On Position

IH		F	PIL
			O
	O	F	T
			O
			N
LO

1.Turn off the wall switch.

2.Turn off all electric power to the appliance if service is to be performed.

Selector Switch in Remote Position

(Optional Remote Control)

Figure 52 - Setting the Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

For morevisit www..com

105706-01B