Desa DVF36TCR, DVF36TCL, DVF36TCR, DVF36TCL, DVF36TCRP, DVF36TCLP Continued, Number Description

Venting Installation

Instructions

Continued

Number Description

E58-45 45° Elbow, Galvanized

E58-90 90° Elbow, Galvanized

FSE58-45 45° Starter Elbow (Dura Vent to FMI Pipe)

FP-58 Firestop Plate

WF-58 Wall Firestop, Galvanized

RF-58-6 Roof Flashing - 0 to 6/12 Pitch, Galvanized

RF-58-12 Roof Flashing - 6/12 to 12/12 Pitch, Galvanized

S-58 Vinyl Siding Standoff,

Galvanized

VT-58 Vertical Round Termination, Galvanized

HHT-58 High WInd Round Horizontal Termination Kit, Galvanized

HTS-58 Square Horizontal Termination, Galvanized

HHTK-58 High Wind Round Horizontal Termination Kit

(Includes Round Termination, Wall Firestop, 45° Elbow)

ST-58-14 14" Snorkel Termination,

Galvanized

ST-58-36 36" Snorkel Termination,

Galvanized

SF-58 Stucco Flashing - For use with HTS-58

VR-58 Vertical Restrictor, Galvanized WS-58 Wall Strap

SC-58 Storm Collar, Galvanized

CS-58 Cathedral Ceiling Support

Installation

WALL SWITCH INSTALLATION

The electronic version uses a 24 VAC current sup- plied from a transformer mounted on the ignition module and is prewired for easy connection to a wall switch (see Figure 31). The millivolt version uses a self generated millivolt current that allows you to activate the gas control valve directly with- out the use of normal household electricity (see Figure 32). Both versions are supplied with a wall switch kit for ready connection and mounting.

WARNING: Do not wire re- mote wall switch to main power supply (Standard 120V house- hold current).

1.To remove the louvers, simultaneously pull both top end spring latches towards the center of the appliance until they are disengaged from locating holes. Repeat for bottom spring latches and pull louvers outward. Reverse the procedure to install louvers back onto the ap- pliance (see Figure 33, page 19).

2.Connect the 18 gauge wires from wall switch to the gas control valve terminals marked TH and TPTH or to the ignition module using the pigtails and wire nut connectors supplied with the appliance.

Route 24V (Supplied)				Wall Switch
Through Electrical
Conduit Bushing				(Supplied)
Electrode	Make Connections
	with Wirenuts
	(Supplied)			(Back
				View)
Transformer
		G	P.
		N
		D V2 L1 IND TS SI	SW V1
Plug 120V AC		Ignition
To Receptacle				18 AWG
		Control
				Red Wire
		Module
G		P.
N V2 L1	IND TS SI	SW V1
D

Figure 31 - Wall Switch Wiring Diagram,

Electronic Units

6AI
7	TH	Wall Switch
	TP	(Supplied)
	TPTH	To
		Thermopile

		ILOT
		P
O N		16AI
T
O		7	TH
L
I
P	L	I
O	O	H	TP
FF
E	A		TPTH

Route Millivolt Wires	(Back
(Supplied) Through Gas	View)
Line Conduit Sleeve

Figure 32 - Wall Switch Wiring Diagram,

Millivolt Units

Note: If any of the original wire supplied must be replaced, use type 18 AWG-105° C (25 feet length maximum) or equivalent.

18 www.desatech.com 112108-01C