CAUTION AVIS
RISK OF ELECTRIC SHOCK • DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO
REFER SERVICING TO QUALIFIED PERSONNEL
ATTENTION: POUR EVITER LES RISQUES DE CHOC
ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE. AUCUN
ENTRETIEN DE PIECES INTERIEURES PAR L'USAGER. CONFIER
L'ENTRETIEN AU PERSONNEL QUALIFIE.
AVIS: POUR EVITER LES RISQUES D'INCENDIE OU
D'ELECTROCUTION, N'EXPOSEZ PAS CET ARTICLE
A LA PLUIE OU A L'HUMIDITE
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Le symbole éclair avec point de flèche à l'intérieur d'un triangle équilatéral est utilisé pour alerter l'utilisateur de la présence à l'intérieur du coffret de "voltage dangereux" non isolé d'ampleur suffisante pour constituer un risque d'éléctrocution.
The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Le point d'exclamation à l'intérieur d'un triangle équilatéral est employé pour alerter les utilisateurs de la présence d'instructions importantes pour le fonction- nement et l'entretien (service) dans le livret d'instruction accompagnant l'appareil.
Table of Contents |
|
1. SAFETY INSTRUCTIONS | 2 |
2. INTRODUCTION | 3 |
Key Features | 4 |
Front Panel Features | 5 |
Rear Panel Features | 5 |
3. INSTALLATION | 7 |
Connections | 7 |
AC Power Considerations | 8 |
4. OPERATION | 9 |
Quick Start | 9 |
Using Inputs | 10 |
Using the BUS A and B Inputs | 10 |
Using the DIRECT OUTPUTS | 11 |
Using OUTPUTS A Through J | 11 |
Using the RECORD Output | 11 |
Using the REMOTE Controls | 11 |
Using the LOGIC I/O | 11 |
Password Protection | 13 |
5. | 13 |
Installing the Software | 13 |
Upgrading the Software | 13 |
Connecting a PC | 14 |
Upgrading the Firmware | 14 |
Overview | 14 |
Top Section | 15 |
Menu Bar | 15 |
Indicators/Presets/Control | 18 |
Button Section | 19 |
Crosspoint Matrix Section | 26 |
Input Section | 27 |
Output Section | 27 |
Group Section | 28 |
Exclusive Enable Program Selection | 28 |
6. SPECIFICATIONS | 29 |
DX810 Block Diagram | 29 |
DX810 Specifications | 30 |
7. SERVICE INFORMATION | 32 |
Appendix A: Logic Input Functions | 33 |
Appendix B: Logic Output Functions | 33 |
Appendix C: Selection Remote Predefined Functions | 34 |
Appendix D: Level Remote Predefined Functions | 35 |
2 – DX810
WARNING — To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION — Internal lithium battery. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
1. SAFETY INSTRUCTIONS
1.Read Instructions — Read all the safety and operation instructions before operating the DX810.
2.Retain Instructions — The safety and operating instructions should be kept for future reference.
3.HEED ALL WARNINGS — Follow all warnings on the DX810 and in these operating instructions.
4.FOLLOW ALL INSTRUCTIONS — Follow all operating and other instructions.
5.Water and Moisture — Do not use the DX810 near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, etc.
6.Ventilation — This DX810 should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug, or similar surface that may block any ventilation openings, or placed in a
7.Heat — Locate the DX810 away from heat sources such as radiators, or other devices which produce heat.
8.Power Sources — Connect the DX810 to a power supply only of the type described in these operation instructions or as marked on the rear panel. If using an external DC power supply or battery pack, be sure the voltage corresponds to the range indicated on the rear panel, and that it is connected with the correct polarity.
9.Power Cord Protection — Route power supply cords so that they are not likely to be walked upon or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit the DX810.
10.Object and Liquid Entry — Do not drop objects into or spill liquids into the inside of the DX810.
11.Damage Requiring Service — The DX810 should be serviced only by qualified service personnel when:
A.The
B.Objects have fallen, or liquid has spilled into the DX810; or
C.The DX810 has been exposed to rain; or
D.The DX810 does not appear to operate normally or exhibits a marked change in performance; or
E.The DX810 has been dropped, or its chassis damaged.
12.Servicing — The user should not attempt to service the DX810 beyond those means described in this operating manual. All other servicing should be referred to the EAW Commercial Service Department.
13.To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.
Pour prévenir les chocs électriques ne pas utiliser cette fiche polariseé avec un prolongateur, un prise de courant ou une autre sortie de courant, sauf si les lames peuvent être insérées à fond sans laisser aucune pariie à découvert.
14.Grounding or Polarization — Precautions should be taken so that the grounding or polarization means of the
15.This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications.
ATTENTION
