EAW DX810 7. SERVICE INFORMATION

32 – DX810

DISCLAIMER

EAW Commercial continually engages in

research related to product improvement, new

materials, and production methods. Design

refinements are introduced into existing products

without notice as a routine expression of that

philosophy. For this reason, any current EAW

Commercial product may differ in some respect

from its published description, but will always equal

or exceed the original design specifications unless

otherwise stated.

EAW Commercial is a trademark of LOUD

Technologies Inc.

All other brand names mentioned are

trademarks or registered trademarks of their

respective holders, and are hereby acknowledged.

7. SERVICE INFORMATION

In the event that your DX810 should require

servicing, please follow these instructions:

1. Call EAW Commercial Tech Support at 1-888-337-

7404, 8 am to 5 pm PST (Monday-Friday). Verify

the problem and obtain a Return Authorization

(RA) Number. Be sure to have the serial number of

the unit when you call. You must have a Return

Authorization Number in order to obtain warranty

service at the factory or at an authorized service

center.

2. Pack the unit in its original packaging.

This is very

important.

EAW Commercial is not responsible for

any damage that occurs during shipping due to

non-conventional packaging. Original packaging

helps to minimize the possibility of shipping

damage.

3. Include a legible note stating your name, return

shipping address (no P.O. boxes), daytime phone

number, and Return Authorization Number. Give

us a detailed description of the problem, including

how we can duplicate it.

4. Write the Return Authorization Number in BIG

BOLD PRINT on the top of the box.

5. Tech Support will tell you where to ship the unit

when you call for an RA Number. We suggest

insurance for all forms of cartage.

© 2004 All Rights Reserved.

LOUD Technologies Inc.

Contents

Main 1 2 3 4 5 6 7 8 POWER COMM PORT COMM PORT DX810 v3.3 INSTRUCTION MANUAL 8x10 Digital Matrix Mixer and Signal Processor Table of Contents 1. SAFETY INSTRUCTIONS CAUTION AVIS 2. INTRODUCTION 1 2 3 4 5 6 7 8 e DX810 DIGITAL MIXER BUS A KEY FEATURES FRONT PANEL FEATURES REAR PANEL FEATURES Page 3. INSTALLATION CONNECTIONS Connecting Balanced Sources To connect a balanced mic or line-level signal: Connecting Unbalanced Sources AC POWER CONSIDERATIONS 4. OPERATION QUICK START Make the Connections Start Up Set the Levels USING INPUTS 1-8 TRIM LEVEL EQ USING THE BUS A AND B INPUTS USING THE DIRECT OUTPUTS USING OUTPUTS A THROUGH J USING THE RECORD OUTPUT USING THE REMOTE CONTROLS DX-SW4 Selection Remote (4-Button/4-LED) Logic Inputs Force On Force Off Input Mute/Enable Output Mute/Enable Group Mute/Enable Preset Recall Combine On Logic Outputs PASSWORD PROTECTION User Level 5. DX-810-PC SOFTWARE (v 3.3) INSTALLING THE SOFTWARE UPGRADING THE SOFTWARE CONNECTING A PC UPGRADING THE FIRMWARE OVERVIEW TOP SECTION Menu Bar Page Page Indicators/Presets/Control Button Section Grp Name: Affected I/O: Action: Function: Name: Function: Condition: Parameter: Page This means that: Initial Setup Secondary Setup for Room Combining Assign Combinations Each input strip has a 3-band EQ comprised of: About Compression: About Gating: Coarse: Fine: Output: Alignment: CROSSPOINT MATRIX SECTION INPUT SECTION OUTPUT SECTION GROUP SECTION To assign or unassign a crosspoint or output to a group: Exclusive Enable Program Selection To configure groups for Exclusive Enable: EAW COMMERCIAL DX810 (v3.3) BLOCK DIAGRAM (6/30/03 DF) 6. SPECIFICATIONS DX810 BLOCK DIAGRAM DX810 SPECIFICATIONS INPUTS / OUTPUTS PANEL CONTROLS PANEL INDICATORS LED METER VALUES DX810 AUDIO PHYSICAL ELECTRICAL PC SYSTEM REQUIREMENTS 7. SERVICE INFORMATION Appendix B: Logic Output Functions Appendix A: Logic Input Functions Logic Input Logic Output Appendix C: Selection Remote Predefined Functions DX-SW4 Remote Switch Control (4-button/4-LED) for DX-810 v3.3 (Firmware v7.06) Appendix D: Level Remote Predefined Functions DX-RVC Remote Volume Control (2-button/12-LED)