EAW DX810 - page 17

DX810 – 17

Note: When changing presets, the faders

change position quickly on-screen, but the audio

actually ramps according to the Ramp Time setting.

Set Powerup Preset

Select this to open the Powerup Preset Selection

window. When None (last state) is selected, the

DX810 returns to its state when it was last turned

off. Click in the Select Powerup Preset box and

drag up or down to select one of the 24 presets to

load on powerup.

Set Global Faders

Select this to open the Global Output Faders

window. Click in the Output Faders are stored: box

to choose whether the output fader settings are

saved with each preset, or the output fader settings

are global and remain at their current settings

regardless of the preset selected.

Windows

About

This provides information about the DX–810–PC

software application, including the version and

personnel credits.

Close Window (Esc)

This closes the window that is currently selected

(front-most) on-screen.

Close All (Ctrl+/)

This closes sub-windows that are currently open on

the screen, leaving just the main window open.

Combine

This toggles the Combine view with the Crosspoint

Matrix view. It duplicates the function of the

Combine button in the Button Section.

Input EQ

This toggles the Input EQ window open and closed.

It duplicates the function of the Input EQ button in

the Button Section.

Contents

Main 1 2 3 4 5 6 7 8 POWER COMM PORT COMM PORT DX810 v3.3 INSTRUCTION MANUAL 8x10 Digital Matrix Mixer and Signal Processor Table of Contents 1. SAFETY INSTRUCTIONS CAUTION AVIS 2. INTRODUCTION 1 2 3 4 5 6 7 8 e DX810 DIGITAL MIXER BUS A KEY FEATURES FRONT PANEL FEATURES REAR PANEL FEATURES Page 3. INSTALLATION CONNECTIONS Connecting Balanced Sources To connect a balanced mic or line-level signal: Connecting Unbalanced Sources AC POWER CONSIDERATIONS 4. OPERATION QUICK START Make the Connections Start Up Set the Levels USING INPUTS 1-8 TRIM LEVEL EQ USING THE BUS A AND B INPUTS USING THE DIRECT OUTPUTS USING OUTPUTS A THROUGH J USING THE RECORD OUTPUT USING THE REMOTE CONTROLS DX-SW4 Selection Remote (4-Button/4-LED) Logic Inputs Force On Force Off Input Mute/Enable Output Mute/Enable Group Mute/Enable Preset Recall Combine On Logic Outputs PASSWORD PROTECTION User Level 5. DX-810-PC SOFTWARE (v 3.3) INSTALLING THE SOFTWARE UPGRADING THE SOFTWARE CONNECTING A PC UPGRADING THE FIRMWARE OVERVIEW TOP SECTION Menu Bar Page Page Indicators/Presets/Control Button Section Grp Name: Affected I/O: Action: Function: Name: Function: Condition: Parameter: Page This means that: Initial Setup Secondary Setup for Room Combining Assign Combinations Each input strip has a 3-band EQ comprised of: About Compression: About Gating: Coarse: Fine: Output: Alignment: CROSSPOINT MATRIX SECTION INPUT SECTION OUTPUT SECTION GROUP SECTION To assign or unassign a crosspoint or output to a group: Exclusive Enable Program Selection To configure groups for Exclusive Enable: EAW COMMERCIAL DX810 (v3.3) BLOCK DIAGRAM (6/30/03 DF) 6. SPECIFICATIONS DX810 BLOCK DIAGRAM DX810 SPECIFICATIONS INPUTS / OUTPUTS PANEL CONTROLS PANEL INDICATORS LED METER VALUES DX810 AUDIO PHYSICAL ELECTRICAL PC SYSTEM REQUIREMENTS 7. SERVICE INFORMATION Appendix B: Logic Output Functions Appendix A: Logic Input Functions Logic Input Logic Output Appendix C: Selection Remote Predefined Functions DX-SW4 Remote Switch Control (4-button/4-LED) for DX-810 v3.3 (Firmware v7.06) Appendix D: Level Remote Predefined Functions DX-RVC Remote Volume Control (2-button/12-LED)