Turning the Projector On/Off | Eiki EIP-3000N specification

Turning the Projector On/Off

Turning the Projector on

Note that the connections to external equip- ment and power outlet should be done be- fore performing the operations written be- low. (See pages 23 to 27.)

Remove the lens cap and press oSTANDBY-ON on the projector or fON on the remote control.

•When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 47 for details.

Info

•English is the factory default language. If you want to change the on-screen display to an- other language, change the language accord- ing to the procedure on page 45.

Lamp indicator

STANDBY-ON button

Note

• About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on.

Blinking in green:The lamp is warming up or shutting down.

Red:The lamp is shut down abnormally or the lamp should be replaced.

• When switching on the projector, a slight flick- ering of the image may be experienced within the first minute after the lamp has been illumi- nated. This is normal operation as the lamp’s

ON button

control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.

• If the projector is put into standby mode and immediately turned on again, the lamp may take some time to start projection.

28

Image 32

Eiki EIP-3000N owner manual Turning the Projector On/Off, Turning the Projector on, Lamp indicator STANDBY-ON button

Contents

EIP-3000N This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified Electrician Iii Page Introduction A. only Product Disposal Using the Menu Screen For Future Reference Contents Reference Cleaning AccessoriesPower Sources Power-Cord Protection Damage Requiring Service Replacement PartsSafety Check Overloading Rest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Potential hazard of glass par Other connected equipment Using the projector in other countriesTemperature monitor function Setup Manual Accessories Optional accessory Projector Height 31 AdjustPart Names and Functions Rear View Output Input 1Audio Input 1 Audio Input Break Timer Picture Mode Attach the cover and slide it until it clicks into place Inserting the BatteriesUsable Range STANDBY-ON Setup and ProjectionQuick Start Adjust the projected image with the Setup Guide Upper side Setting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount Setup 120 Projection PRJ ModeExample Normal Mode Picture Size Screen Size and Projection Distance Normal ModeStretch Mode Connections Input Terminals and Connectable Main Equipment Samples of Cables for Connection Computer To INPUT1 terminal To Audio Terminal Connecting to a ComputerTo audio output terminal To RGB output terminal Connecting to Video Equipment When using an S-video cable INPUT3 Connecting to a Monitor with RGB Input Terminal When using a composite video cable INPUT4 Controlling the Projector by a Computer To RS-232C terminal AC socket To AC outlet Connecting the Power CordWhen connecting to the LAN terminal using a LAN cable Turning the Projector on Lamp indicator STANDBY-ON buttonTurning the Projector On/Off On-screen Display confirmation message Power indicator STANDBY-ON buttonOutlet after the cooling fan stops About the Setup Guide Adjusting the Projected Image Adjusting the FocusAdjusting the Screen Size Image Projection Adjusting the Height Use the rear adjustment foot to make the projector levelAdjust lever Make small adjustments Rear adjustment foot Height AV Mute button Volume buttons Input buttons Switching the Input ModeAdjusting the Volume Press g Keystone to enter Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Press g Keystone Resize Mode Press Hresize Video Operating with the Remote Control Auto Sync Auto Sync AdjustmentDisplaying and Setting the Break Timer Selecting the Picture Mode Input 1 Component/INPUT Component/INPUT 3/INPUT Menu ItemsInput 1 RGB/INPUT2 RGB Projector adjustment PRJ-ADJ menu Items you can set with the Help menu Help menu n Using the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Press Bmenu To adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press hENTER Example Picture screen menu for Input 3 mode Picture Adjustment Picture menu1Selecting the Picture Mode 2Adjusting the Image 3Adjusting the Color Temperature5Lamp Setting Progressive Adjusting the Projected Image SCR ADJ menu 1Setting the Resize Mode2Adjusting the Image Position 3Keystone Correction 4Setting the On-screen Display 6Selecting the Setup GuideReversing/Inverting Projected Images 5Selecting the Background Image 2Auto Sync Auto Sync Adjustment 3Auto Power Off Function4Setting the Confirmation Sound System Sound 5Speaker Setting 7Fan Mode Setting 9Checking the Lamp Life Status8System Lock Function Select System Lock, then press hENTER or Q ATaking the Keylock off Enter the same keycode in Re- confirmLocking the Operation Buttons 1Setting a Password 2DHCP Client Setting 3TCP/IP Setting4Confirming the Projector Information Set the TCP/IP manually Troubleshooting with the Help menu Utilizing the Help menu func TionsPress Oor Qto select Help, then MENU/HELP Maintenance Cleaning the projector Maintenance Indicators Temperature warning indicator Lamp indicator Power indicator Please exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer Computer Compatibility Chart PC/MAC Troubleshooting 23-27 Input 1 Component Specifications Product type Projector Model EIP-3000N Video system Dimensions Index Canada Eastern EuropeDeutschland & Österreich Japan & Worldwide