Manuals / Eiki / Computer Equipment / Projector

Eiki EIP-WX5000L specifications Video Wall Projection, Info

Models: EIP-WX5000 EIP-WX5000L

1 59

Page 44

Video Wall Projection

Usually, a costly image-processing device is required to set up a video wall projection. This projector has built-in video wall capability that doesn’t require additional equipment.

Info

•Before setting up the video wall projection, install Internet Explorer (version 5.0 or later).

•Video wall is not compatible with resolutions higher than SXGA.

•Image quality may deteriorate when picture signals are input through multiple projectors with an RGB cable or an RCA cable in a daisy chain connection.

Page 44

Image 44

Eiki EIP-WX5000L specifications Video Wall Projection, Info

Contents

SETUP MANUAL Connecting Pin AssignmentsRS-232C Specifications and Commands DimensionsSetting up the Screen Standard Setup Front ProjectionSide View Top ViewScreen Size and Projection Distance Throw DistanceThe graph below is for 100 inches 254 cm screen with 1610 normal mode ScreenScreen Size and Projection Distance F2.5, f=25.5-32 mm1610 Signal Input Normal Mode 43 Signal Input Normal ModeFixed Wide Lens AH-55201 F2.5, f=11.6 mm1610 Signal Input Normal Mode 43 Signal Input Normal ModeFixed Wide Lens AH-55301 F2.5, f=17.1 mm1610 Signal Input Normal Mode 43 Signal Input Normal ModeWide-zoom Lens AH-55401 F2.5, f=21.2-25.8 mm1610 Signal Input Normal Mode 43 Signal Input Normal ModeTele-zoom Lens AH-55601 F2.5, f=31.9-42.5 mm1610 Signal Input Normal Mode 43 Signal Input Normal ModeTele-zoom Lens AH-55701 F2.5, f=40.8-62.8 mm1610 Signal Input Normal Mode 43 Signal Input Normal ModeTele-zoom Lens AH-55801 F2.5, f=62.1-97.8 mm1610 Signal Input Normal Mode 43 Signal Input Normal ModeConnecting Pin Assignments DVI-D Terminal 24 pin connectorHDMI Terminal RGB InputConnecting Pin Assignments RS-232C Cable recommended connection D-sub 9-pin female connectorLAN Terminal LAN RJ-45 SignalWired Remote Control Terminal Specifications Specifications of wired remote control inputEIKI remote control signal format Function and transmission codesRS-232C Specifications and Commands Computer controlCommunication conditions Basic formatCommands RS-232C Specifications and CommandsExample When turning on the projector, make the following setting P O W RRS-232C Specifications and Commands CONTROL CONTENTSCOMMAND Power ONRS-232C Specifications and Commands CONTROL CONTENTSCOMMAND Power ONRS-232C Specifications and Commands CONTROL CONTENTSCOMMAND Power ONRS-232C Specifications and Commands 1 Lamp Timer Reset command is available only in standby modeSetting up the Projector Network Environment Network settings on the computer1. Connecting the projector to a computer 2. Setting an IP address for the computer1. Connecting the Pro- jector to a Computer Setting up the Projector Network Environment3 Plug the power cord into the AC socket of the projector 1 Disconnect the computer’s LAN cable from the existing network2. Setting an IP Address for the Computer 2 Click “start”, and click “Control Panel”Click “Properties” Setting up the Projector Network Environment6 Confirm or change an IP address for the setup computer 5 Click “Internet Protocol Version4 TCP/IPv4”, and click the “Properties” button Setting up the Projector Network EnvironmentSetting up the Projector Network Environment 3. Setting up a Network Connection for the Projector1 Start Internet Explorer version Click the “Apply” button Setting up the Projector Network EnvironmentControlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later 1 Start Internet Explorer version 5.0 or later on the computerConfirming the Projector Controlling the ProjectorControlling the Projector via LAN Status StatusSetting and Adjusting the Setting the SecurityProjector Settings & Adjustments Network - SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail - Originator Settings GeneralMail - Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs Controlling the Projector via LANSetting the Projector Using RS-232C or Telnet When Connecting Using RS-232C8 Input “setup” and press the “Enter” key 1 Launch general purpose terminal emulatorWhen Connecting Using Telnet Setting the Projector Using RS-232C or Telnet6 Input “setup” and press the “Enter” key 5 “Password” is displayed. Input the password and press the“Enter”keySETUP MENU Main Menu ADVANCED SETUP MENUSetting the Projector Using RS-232C or Telnet SETUP MENUControlling the Projector Using RS-232C or Telnet View Setting Detail ListVView All Setting Set ItemsSave Settings and Quit Controlling the Projector Using RS-232C or TelnetQuit without Saving Set SSave & QuitIP Address Setting Default Gateway SettingSubnet Mask Setting User Name SettingPassword Setting Projector Name SettingDHCP Client Setting 5PasswordDisconnecting All Connec Setting Auto Logout TimeEntering ADVANCED SETUP MENU Data Port SettingSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses ADVANCED5Network Ping TestSetting of Search Port Return to Default SettingsADVANCED!Restore Default Setting Return to Main MenuStack Projection InfoSetting up the Stack Projection 1 Set the “Stack Setting” of the pro2 Set the “Stack Setting” of the pro- jector 2 to “Slave” Stack ProjectionApplication 9 Turn on the projectors first, then turn on the computerProjector Master Projector SlaveVideo Wall Projection InfoSetting up the Video Wall Projection Basic Video Wall ProjectionProjector Projector1 Access one of the four projectors via Internet Explorer Video Wall Projection2 Click “Video Wall” on the menu 3 Select “2 X 2” on “Division”Adjusting the Position Horizontally and Vertically Returning to the Default Video Wall SetupAssigning the Projected Image on the Video Wall Setup Front ProjectionNotes on the Wide Video Wall Projection Video Wall ProjectionSetting up the Video Wall Projection Application Video Wall ProjectionProjector Master Projector SlaveFollow the procedure below after setting up the basic connection 1 Change the TCP/IP settings for the computer as shown below2 Change the TCP/IP settings for Preparation5 Access the projector 1 from the computer via Internet Explorer Click “Stack” on the menu Select “Master” on “Stack Setting”10 Access the projector 2 from the computer via Internet Explorer Click “Stack” on the menu Select “Slave” on “Stack Setting”Video Wall Projection MasterSlave COMPUTER1Resetting the Lamp Timer of the Projector via LAN code” field. From the “Connect using” drop-down menu, select2 Enter a name in the “Name” field, and click “OK” 3 If you are required to enter the area code, enter it in the “AreaResetting the Lamp Timer of the Projector via LAN 6 Click the “Settings” tab, and then click “ASCII Setup”5 Click “Properties” on the “File” menu 10 Close HyperTerminalTroubleshooting When connecting the projector using serial-connectionCheck the network settings for the computer and the projector Communication cannot be established with the projectorTroubleshooting Troubleshooting Dimensions Units inches mmSide View Front ViewProjector and Lens Dimensions DimensionsWhen AH-55201 is installed When AH-55301 is installed